Alamo 3109 manual Dismounting Loader, Mounting Loader

Page 40

ASSEMBLY

ASSEMBLY

Dismounting Loader

1.Locate tractor and loader on firm level ground.

2.Rotate parking stands from storage position to operation position by removing hair pins and clevis pins. Reinstall clevis pin and hair pin when parking stands are in operation position. See Figure Asm-L-0167.

3.Level and lower bucket to ground. Rotate bucket down slightly to remove pressure on hitch pins (See Figure Asm-L-0168).

4.Remove lynch pins and hitch pins from mounting.

5.Start tractor engine and release brakes. Retract lift cylinders, allowing parking stands to support weight of loader. Drive tractor forward slightly so parking stands are firmly positioned. Operate loader control lever to extend lift cylinders, allowing top of loader upright to rotate forward out of upper mounting saddle. Operate loader control lever to retract bucket cylinder, which will curl bucket backward causing the loader upright to lift off of the mounting shaft. Continue to curl bucket until loader upright has rotated upward from the mounting position to clear front tires or fenders on tractor.

6.Stop engine and apply brakes. Disconnect hydraulic hoses from tractor.

7.Start tractor engine and release brakes. Slowly back tractor out of loader.

Mounting Loader

Mounting is basically reverse of dismounting.

1.Slowly drive tractor up to loader. Shut off tractor and apply brakes.

2.Connect hydraulic hoses.

3.Start engine and release brakes. Operate loader control lever to extend bucket cylinder, which will rotate bucket down, causing the loader upright to rotate downward placing mounting shaft in mounting pocket. Operate loader control lever to retract lift cylinders, causing the top of loader upright to rotate rearward. Continue to rotate loader upright into mounting saddle until upright will no longer rotate.

4.Shut off tractor, apply brakes.

5.Install hitch pins and linch pins, into mounting.

6.Remove hair pins and clevis pins from parking stands, rotate stands into storage position and secure with clevis pins and hair pins (Figure Asm-L-0167).

3109 01/11

Assembly Section 3-6

© 2011 Alamo Group Inc.

Image 40

Contents 3109 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section Safety General Safety Instructions and Practices3109 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 Safety Safety 3109 01/11 Safety Section SL-33 SPU-2 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Storage and Parking Safety Instructions and Practices Concluding Safety Instructions and PracticesDecal Location QTY Level Description Model Name Loader Positions 3109 01/11 Safety Section Loader Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Assembly InstructionsAssembly Proper Ballasting and Wheel Spacing Dismounting Loader and Mounting Loader to Tractor Dismounting Loader Mounting LoaderInstalling Bucket Level Indicator Asm-L-0169Attaching Pin on Bucket Assembling Quick Attach Device Installing Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Rops and Seat Belt Tractor RequirementsTractor Lighting and SMV Emblem Getting On and Off the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/Service Loader Pre-Operation Inspection and ServiceMount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and Loader Operation Operation SL-33 Operation Operating the Loader Filling the BucketOperation Lifting the Load Carrying the LoadDumping the Bucket Lowering the Bucket Operating with Float Control Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Transporting the Tractor and Implement Loader StorageShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyProblem Possible Cause Remedy Maintenance Section Maintenance 3109 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Cylinder Service Lift and Bucket Cylinder DisassemblyLift and Bucket Cylinder Reassembly StorageMaintenance Proper Torque for Fasteners Maintenance Maintenance Rhino To the OWNER/OPERATOR/DEALER SOM-01/11 F-4293C Printed U.S.A