Exmark 850, 00 & Higher manual California

Page 2

WARNING

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

Important: IMPORTANT The engine in this product is not equipped with a spark arrester muffler. It is a violation of California Public Resource Code (CPRC) Section 4442 to use or operate this engine on any forest-covered, brush-covered, or grass-covered land as defined in CPRC 4126. Other states or federal areas may have similar laws.

To acquire a spark arrester for your unit, see your Engine Service Dealer.

This spark ignition system complies with Canadian ICES-002 Ce système d’allumage par ètincelle de vèhicule est conforme à la norme NMB-002 du Canada

The enclosed Engine Owner’s Manual is supplied for information regarding The U.S. Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance and warranty.

Keep this engine Owner’s Manual with your unit. Should this engine Owner’s Manual become damaged or illegible, replace immediately. Replacements may be ordered through the engine manufacturer.

Exmark reserves the right to make changes or add improvements to its products at any time without incurring any obligation to make such changes to products manufactured previously. Exmark, or its distributors and dealers, accept no responsibility for variations which may be evident in the actual specifications of its products and the statements and descriptions contained in this publication.

©2010 Exmark Mfg. Co., Inc.

 

Contact us at www.Exmark.com.

Industrial Park Box 808

 

Printed in the USA

2

Beatrice, NE 68310

All Rights Reserved

Image 2
Contents Metro California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Slope OperationMaintenance and Storage Safety and Instructional Decals 403143 98-5954 103-1623 117-2718 103-5626 Systems SpecificationsModel Numbers Dimensions Torque RequirementsControls Product OverviewOperation Operator Presence Control OPC LeversThrottle Control Off-Run SwitchChoke Control Drive LeversPre-Start Operating InstructionsDriving the Machine For ECS HandlesTransporting a Unit TransportingChanging Gears Maintenance Recommended Maintenance SchedulesReplacing the Discharge Deflector Check Engine Oil LevelCheck Mower Blades Check for Loose Hardware Check Safety Interlock SystemService Air Cleaner Check Condition Of Belts Change Engine OilCheck Tire Pressures Lubricate Grease FittingsCheck Spark Plugs Change Fuel FilterCopper-Based Anti-seize Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Dielectric GreaseAdjustments Adjusting the Cutting HeightAdjusting the Axle Position Adjusting the Number of Spacers below Caster Support Hub Adjusting the Cutting Height with Blade SpacersEngine to Mower Deck Belt AdjustmentWheel Drive Belt Pulley Scrapers Transmission BeltBlade Brake Adjustment Inch Deck Shown for Reference OnlyBelt Guide Adjustment Brake and Wheel Drive Linkage AdjustmentLeft Side Shown Shifter Lever Adjustment Right Side of Unit ShownHandle Height Adjustment Shifter Detent AdjustmentPTO Safety Switch Adjustment Wheel Drive Spring Tension AdjustmentClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsWaste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Motor Oil DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Schematics Exmark Commercial Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByThis page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 52 pages 62.21 Kb Manual 32 pages 16.59 Kb Manual 28 pages 32.2 Kb Manual 60 pages 29.4 Kb Manual 24 pages 21.56 Kb Manual 48 pages 5.05 Kb Manual 40 pages 46.04 Kb