Exmark VH3615KA, Vh3615ka, Vh4815ka manual Pre-Start

Page 18

Once the engine has started, move the throttle control lever to the midway point and allow the engine to warm-up before going to full throttle.

4.1.7“Off-Run” Switch: Located on the console. Turn key to the “Run” position to allow the engine to be started. Turn key to the “Off” position to shut engine off.

4.1.8Fuel Shut-Off Valve: Installed in the fuel line midway between the tank and engine. The fuel shut-off valve is used to shut off the flow of fuel when parking inside a building, during transportation to and from the job sites, and when the machine will not be used for a few days.

Rotate valve 1/4 turn clockwise to shut fuel off.

Rotate valve 1/4 turn counter-clockwise to turn fuel on.

4.1.9Drive Wheel Release Valves: Located on the top rear corner of the hydrostatic pumps. Drive wheel release valves are used to release the hydro-static drive system to allow the machine to be moved by hand without the engine running. Turn valves one-half turn counterclockwise to release the drive system.

Turn clockwise to reset the drive system. Do Not over-tighten.

4.1.10Cold Start Kit: Located on the right hand side of engine deck, below and slightly ahead of the hydro control shield. The cold start kit is used to ease the starting of the unit in cold weather or when the unit has not been operated for a period of time. The cold start kit moves the idler pulley away from the pump belt, releasing the tension on the belt which allows the engine to turn over with less resistance. See Section 4.3.2.

4.1.11Tracking Adjustment Knob: Located on the right-hand side of the rear of the fuel tank support. Can be adjusted so that machine will “track” straight ahead with drive levers released.

4.2Pre-Start

DANGER

POTENTIAL HAZARD

In certain conditions gasoline is extremely flammable and highly explosive.

WHAT CAN HAPPEN

A fire or explosion from gasoline can burn you, others, and cause property damage.

HOW TO AVOID THE HAZARD

DO NOT smoke while refueling, and stay away from an open flame or where gasoline fumes may be ignited by spark.

Refuel only in a well ventilated area, or refuel outdoors.

Store gasoline in an approved container and keep it out of the reach of children.

Add fuel before starting the engine. Never remove the cap of the fuel tank or add fuel when engine is running or when the engine is hot.

Never fill the fuel tank so that the gasoline level rises above a level that is 1/2” below the bottom of the filler neck to allow for gasoline expansion and prevent fuel spillage.

If fuel is spilled, DO NOT attempt to start the engine. Move away from the area of the spill and avoid creating any source of ignition until fuel vapors have dissipated.

- 13 -

Image 18
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Assembly Instructions SafetySpecifications Maintenance & AdjustmentsSafety Alert Symbol SafetyYour Safety is Involved TrainingPotential Hazard Operation Maintenance and Storage Safety Signs Riding AttachmentsPage Specifications Dimensions Wheel Drive SystemTires Assembly Instructions Torque RequirementsUpper Handle Mounting HP Kawasaki Speed Control Throttle Cable HOOK-UP Hydro Control Linkage Swivel & Drive Linkage SwivelDrive Linkage to Drive Lever Operation Instructions Drive LEVER, Neutral Lock Latch OperationPre-Start Operating Instructions Potential Hazard Rotating blades under the mower deck are dangerous Maintenance & Adjustments TransportingPeriodic Maintenance Do not OverfillBlade Bolt Installation Must stopService Interval After First 250 hrs, then yearly thereafter Charge Pump Location Grease Lubrication Chart Fitting Initial Quantity Service Locations Pumps IntervalSpray Lubricant Chart Pivot PointAdjustments Potential Hazard Cutting Height Adjustment 1 to 4 1/4 Axle NO. of Spacers Number of 1/4 Blade Spacers PositionBlade Engagement Linkage Cutter Deck Belt Adjustment Blade Brake AdjustmentNeutral Safety Switch Adjustment Belt Guide LocationHydro Drive Linkage Adjustment Hydro Control LINK/SWIVEL AdjustmentDrive Lever and Latch in Neutral Position Mower Tracks to Left or Right Trouble ShootingBlades do not Stop When Disengaged Mower Cuts UnevenlyProblem Engine TroubleshootingEngine Troubleshooting Table Mower Deck Belt RoutingWiring Diagram Hydraulic Diagram Warranty Page Fold Along Appropriate Line See EXMARK’S Complete Line of Products for Turf Care