Exmark FR27KC, FR20KC, FR23KC manual

Page 36

d)Locate the park brake spring assembly. See Figure 7. There should be a gap of 1/8” (3 mm) between the yoke and thin nyloc nut on the brake bolt. If necessary, rotate the thin nyloc nut to obtain the 1/8” gap.

FIGURE 7

e)If park brake does not fully disengage when the lever is disengaged check the brake rod linkage assembly. The assembly should measure 7 3/8” (18.7 cm) from the center of the ball joint to the center of the lower end of the linkage rod. See Figure 8.

FIGURE 8

f)If the linkage does not measure 7 3/8” (18.7 cm) or still does not disengage as desired, remove the bolt that secures the ball joint to the brake lever and loosen the jam nut next to the ball joint. Rotate the ball joint in half-turns counter-clockwise until desired disengagement is obtained.

4.2.4Adjust Throttle Lever Tension.

a)Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

b)Tension in throttle lever can be adjusted by adjusting the tightness of the lever pivot bolt, which is located under the console. See Figure 9.

FIGURE 9

31

Page 35 Page 37
Image 36
Page 35 Page 37
Contents For Serial Nos 600,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Potential Hazard Operation Tip-over could cause serious injury or death Potential Hazard Page Maintenance and Storage Safety Signs LocationPage Specifications EngineFuel System Electrical SystemOperator Controls Hydrostatic Ground Drive SystemDimensions TiresOperation Instructions Torque RequirementsControls Potential Hazard PRE-START Operating InstructionsStarting Engine Transporting Tip-over of the unit could cause serious injury or death Maintenance & Adjustments Periodic MaintenanceService Interval Daily Service Interval Monthly Service Interval Daily or more often in dry conditionsService Interval Daily Check starting circuit Check the kill circuitsCheck the PTO circuit Service Interval 100 hrs PTO must not engageFor 27 HP Kohler Units For 20 HP and 23 HP Kohler UnitsService Interval 40 hr Service Interval 40 hrs Service Interval Refer to chartService Interval Once Yearly Service Interval 160 hrsService Interval Yearly Service Interval 80 hrsService Interval As Required Service Interval After First 250 hrs Then yearly thereafterAdjustments Service Interval 500 hrsPage Set neutral Page Weight transfer springs may have stored energy Trouble Shooting Waste DisposalEngine Troubleshooting Table Engine will not StartElectrical Diagram Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Evaporative Emission Control Warranty Statement Page Page See EXMARK’S Complete Line of Accessories

FR23KC, FR20KC, FR27KC specifications

The Exmark FR27KC, FR23KC, and FR20KC stand out as exemplary models in the commercial-grade zero-turn mower segment, each designed with unique features and advanced technologies for efficiency and durability. These models are powered by Kawasaki engines, renowned for their reliability and performance, ensuring users can tackle tough mowing tasks with ease.

The FR27KC boasts a powerful 27-horsepower engine, making it ideal for larger properties and demanding landscapes. Its robust design and high torque output allow it to handle thicker grasses and challenging terrains effectively. This model features a 60-inch UltraCut deck, which offers superior cutting performance and striping ability. The deck is designed with a unique airflow system that ensures clippings are discharged evenly, promoting a clean and professional look.

In contrast, the FR23KC features a slightly smaller engine with 23 horsepower. This model is perfect for mid-sized lawns and provides a balance of power and maneuverability. It is equipped with a 52-inch deck, allowing for quick and efficient mowing. The FR23KC also comes with Exmark's patented mulching capability, which not only recycles grass clippings but also enhances soil health by returning nutrients to the ground.

The FR20KC is the entry-level model in this range, featuring a 20-horsepower engine. Despite its smaller size, the FR20KC packs a punch with its 48-inch cutting deck, making it suitable for residential properties or smaller commercial tasks. This model emphasizes user comfort with adjustable seating and easy-to-reach controls, making it accessible for users of all skill levels.

All three models share advanced features such as Exmark's patented Hydro-Drive system, which provides smooth and precise control over the mower's speed and direction, enhancing maneuverability. Additionally, they come with heavy-duty components, ensuring longevity and reliability in demanding conditions. Ergonomics has been a significant consideration in these designs, with padded seat options and intuitive control layouts that reduce operator fatigue.

In summary, the Exmark FR27KC, FR23KC, and FR20KC models cater to different mowing needs while incorporating advanced technologies and exceptional build quality. Whether tackling sprawling lawns or managing tight spaces, these mowers deliver performance, comfort, and durability, making them a worthwhile investment for any serious landscaper or homeowner.
Top Page Image Contents