Exmark FR27KC, FR20KC, FR23KC manual Evaporative Emission Control Warranty Statement

Page 45

10.Evaporative Emission Control Warranty Statement

California Evaporative Emission Control Warranty Statement

Your Warranty Rights and Obligations

Introduction

The California Air Resources Board and Exmark Manufacturing Company are pleased to explain the evaporative emission control system’s warranty on your 2006 model year equipment. In California, new equipment that uses small off-road engines must be designed, built, and equipped to meet the State’s stringent anti-smog standards. Exmark Manufacturing Company must warrant the evaporative emission control system on your equipment for two years provided there has been no abuse, neglect or improper maintenance of your equipment.

Your evaporative emission control system may include parts such as: fuel lines, fuel line fittings, and clamps.

Manufacturer’s Warranty Coverage:

This evaporative emission control system is warranted for two years. If any evaporative emission-related part on your equipment is defective, the part will be repaired or replaced by Exmark Manufacturing Company.

Owner’s Warranty Responsibilities:

ƒAs the equipment owner, you are responsible for performance of the required maintenance listed in your Operator’s Manual. Exmark Manufacturing Company recommends that you retain all receipts covering maintenance on your equipment, but Exmark Manufacturing Company cannot deny warranty solely for the lack of receipts.

ƒAs the equipment owner, you should however be aware that Exmark Manufacturing Company may deny you warranty coverage if your emission warranty parts have failed due to abuse, neglect, or improper maintenance or unapproved modifications.

ƒYou are responsible for presenting your equipment to an Authorized Service Dealer as soon as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your warranty coverage, you should contact Exmark Manufacturing Company at 1-402-223-6375.

Defects Warranty Requirements:

1.The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser.

2.General Evaporative Emissions Warranty Coverage. The emission warranty parts must be warranted to the ultimate purchaser and any subsequent owner that the evaporative emission control system when installed was:

A.Designed, built, and equipped so as to conform with all applicable regulations; and

B.Free from defects in materials and workmanship that causes the failure of a warranted part for a period of two years.

3.The warranty on evaporative emissions-related parts will be interpreted as follows:

A.Any warranted part that is not scheduled for replacement as required maintenance in the written instructions must be warranted for the warranty period of two years. If any such part fails during the period of warranty coverage, it must be repaired or replaced by Exmark Manufacturing Company. Any such part repaired or replaced under the warranty must be warranted for a time not less than the remaining warranty period.

B.Any warranted part that is scheduled only for regular inspection in the written instructions must be warranted for the warranty period of two years. A statement in such written instructions to the effect of “repair or replace as necessary” will not reduce the period of warranty coverage. Any such part repaired or replaced under warranty must be warranted for a time not less than the remaining warranty period.

C.Any warranted part that is scheduled for replacement as required maintenance in the written instructions must be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part must be repaired or replaced by Exmark Manufacturing Company. Any such part repaired or replaced under warranty must be warranted for a time not less than the remainder of the period prior to the first scheduled replacement point for the part.

D.Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at an Authorized Service Dealer.

E.Notwithstanding the provisions of subsection (D) above, warranty services or repairs must be provided at an Authorized Service Dealer.

F.The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective, provided that such diagnostic work is performed at an Authorized Service Dealer.

G.Throughout the evaporative emission control system's two year warranty period, Exmark Manufacturing Company must maintain a supply of warranted parts sufficient to meet the expected demand for such parts.

H.Manufacturer approved replacement parts must be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner. Such use will not reduce the warranty obligations of Exmark Manufacturing Company.

I.The use of any add-on or modified parts will be grounds for disallowing a warranty claim made in accordance with this article. Exmark Manufacturing Company will not be liable under this Article to warrant failures of warranted parts caused by the use of an add-on or modified part.

J.Exmark Manufacturing Company shall provide any documents that describe the warranty procedures or policies within five working days of request by the Air Resources Board.

Emission Warranty Parts List:

The following list includes the parts covered under this warranty:

Fuel Lines

Fuel Line Fittings

Clamps

40

Image 45
Contents For Serial Nos 600,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Your Safety is Involved SafetySafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Potential Hazard Operation Tip-over could cause serious injury or death Potential Hazard Page Maintenance and Storage Location Safety SignsPage Engine SpecificationsFuel System Electrical SystemHydrostatic Ground Drive System Operator ControlsTires DimensionsOperation Instructions Torque RequirementsControls Potential Hazard Operating Instructions PRE-STARTStarting Engine Transporting Tip-over of the unit could cause serious injury or death Maintenance & Adjustments Periodic MaintenanceService Interval Daily Service Interval Daily or more often in dry conditions Service Interval MonthlyService Interval Daily Check starting circuit Check the kill circuitsCheck the PTO circuit PTO must not engage Service Interval 100 hrsFor 27 HP Kohler Units For 20 HP and 23 HP Kohler UnitsService Interval 40 hr Service Interval Refer to chart Service Interval 40 hrsService Interval 160 hrs Service Interval Once YearlyService Interval 80 hrs Service Interval YearlyService Interval After First 250 hrs Then yearly thereafter Service Interval As RequiredService Interval 500 hrs AdjustmentsPage Set neutral Page Weight transfer springs may have stored energy Waste Disposal Trouble ShootingEngine will not Start Engine Troubleshooting TableElectrical Diagram Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Evaporative Emission Control Warranty Statement Page Page See EXMARK’S Complete Line of Accessories

FR23KC, FR20KC, FR27KC specifications

The Exmark FR27KC, FR23KC, and FR20KC stand out as exemplary models in the commercial-grade zero-turn mower segment, each designed with unique features and advanced technologies for efficiency and durability. These models are powered by Kawasaki engines, renowned for their reliability and performance, ensuring users can tackle tough mowing tasks with ease.

The FR27KC boasts a powerful 27-horsepower engine, making it ideal for larger properties and demanding landscapes. Its robust design and high torque output allow it to handle thicker grasses and challenging terrains effectively. This model features a 60-inch UltraCut deck, which offers superior cutting performance and striping ability. The deck is designed with a unique airflow system that ensures clippings are discharged evenly, promoting a clean and professional look.

In contrast, the FR23KC features a slightly smaller engine with 23 horsepower. This model is perfect for mid-sized lawns and provides a balance of power and maneuverability. It is equipped with a 52-inch deck, allowing for quick and efficient mowing. The FR23KC also comes with Exmark's patented mulching capability, which not only recycles grass clippings but also enhances soil health by returning nutrients to the ground.

The FR20KC is the entry-level model in this range, featuring a 20-horsepower engine. Despite its smaller size, the FR20KC packs a punch with its 48-inch cutting deck, making it suitable for residential properties or smaller commercial tasks. This model emphasizes user comfort with adjustable seating and easy-to-reach controls, making it accessible for users of all skill levels.

All three models share advanced features such as Exmark's patented Hydro-Drive system, which provides smooth and precise control over the mower's speed and direction, enhancing maneuverability. Additionally, they come with heavy-duty components, ensuring longevity and reliability in demanding conditions. Ergonomics has been a significant consideration in these designs, with padded seat options and intuitive control layouts that reduce operator fatigue.

In summary, the Exmark FR27KC, FR23KC, and FR20KC models cater to different mowing needs while incorporating advanced technologies and exceptional build quality. Whether tackling sprawling lawns or managing tight spaces, these mowers deliver performance, comfort, and durability, making them a worthwhile investment for any serious landscaper or homeowner.