Exmark E-Series manual Dimensions, Hydrostatic Ground Drive System, Tires & Wheels, Cutting Deck

Page 16

Specifications

armrests, integral safety switch, and seat vibration isolation system.

Optional seat accessories for units with standard seats:

Custom ride suspension system to enhance Standard Seat. Adds approximately 3 inches (7.6 cm) to seat height.

Deluxe suspension seat with high back, (dampened, adjustable spring suspension), armrests, and integral safety switch. Adds approximately 1/2 inch (1.3 cm) to seat height.

Mounting: Adjustable fore and aft on seat tracks.

Armrests: Molded flip-up armrests.

Seat Safety Switch:

Integrated seat switch. Time delay seat switch eliminates rough ground cut-outs.

Hydrostatic Ground Drive System

Two unitized hydrostatic transmissions: Hydro Gear ZT2800

Hydraulic Oil Type: Exmark Premium Hydro Oil.

Hydraulic Oil Capacity: 77 oz (2.3 L) per side

Hydraulic Filter: P/N 109-3321

Speeds:

0-7 mph (11.3 km/hr) forward.

0-4 mph (6.4 km/hr) reverse.

Drive wheel release valves allow machine to be moved when engine is not running.

Tires & Wheels

 

Drive

Front Caster

 

Pneumatic (Air

Pneumatic (Air

 

filled)

filled)

Quantity

2

2

Tread

Turf Master

Smooth

 

 

 

Size

20 x 8.00-10

13 x 5.00-6

 

 

 

Ply Rating

4

2

Pressure

13 psi (90 kPa)

13 psi (90 kPa)

Cutting Deck

• Cutting Width:

48 inch Deck: (121.9 cm)

52 inch Deck: (132.1 cm)

Discharge: Side

Blade Size: (3 ea.)

48 inch Deck: 16.25 inches (41.3 cm)

52 inch Deck: 18.00 inches (45.7 cm)

Blade Spindles: Solid steel spindles with .67 inch (17 mm) I.D. bearings.

Deck Drive: “B” Section belt with self-tensioning idler.

Electric clutch: 125 ft-lb Mag Stop

Deck: Full floating deck is attached to out-front support frame. Anti-scalp rollers provide maximum turf protection. Deck design allows for bagging, mulching or side discharge.

48 inch Deck: 3 anti-scalp rollers

52 inch Deck: 3 anti-scalp rollers

Deck Depth:

48 inch Deck: 4.0 inches (10 cm)

52 inch Deck: 4.0 inches (10 cm)

Cutting Height Adjustment:

Foot activated lever is used to adjust the cutting height from 1 1/2 inch (3.8 cm) to 5 inches (12.7 cm) in 1/4 inch (6.4 mm) increments.

Mulching Kit: Optional.

Dimensions

Overall Width:

 

48 inch Deck

52 inch Deck

Without Deck

44.1

inches

44.1

inches

 

(112.0 cm)

(112.0 cm)

Deflector Up

48.0

inches

52.8

inches

 

(121.9 cm)

(134.1 cm)

Deflector Down

59.2

inches

64.0

inches

 

(150.4 cm)

(162.6 cm)

16

Image 16
Contents Pioneer E-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 109-6014 116-1119 107-2102 116-1121 116-3303 116-4465 116-4430 Model Numbers SpecificationsSystems Dimensions Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckTorque Requirements Product Overview Operation ControlsMotion Control Levers Choke ControlIgnition Switch Fuel Shut-Off Valve Throttle ControlBrake Lever Hour MeterPTO Engagement Switch Drive Wheel Release ValvesPre-Start Operating InstructionsDeck Lift Pedal Transport LockStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Stopping the Engine Disengaging the PTODriving the Machine Adjusting the Cutting Height Adjusting the Anti-Scalp RollersTransporting a Unit TransportingLoading a Unit Operation Maintenance Recommended Maintenance SchedulesRecommended Jump Starting Procedure Check Battery ChargeCheck Engine Oil Level Do Not jump start a weak battery if these conditions exist Check Mower BladesCheck Safety Interlock System Service DealerService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Check Spark PlugsService Interval After the first 100 hours Change Hydraulic System Filter and FluidCheck Spark Arrester if equipped Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseAdjusting the Blade Slope Deck LevelingPump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Motion Control Handle Adjustment Full Forward Tracking AdjustmentMotion Control Linkage Adjustment Adjusting the Seat Ride Suspension Electric Clutch AdjustmentClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Fins Clean Debris From MachineBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Schematics Electrical DiagramElectrical Logic Schematic Pioneer E-Series Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options