Exmark E-Series manual Motion Control Handle Adjustment, Full Forward Tracking Adjustment

Page 37

Maintenance

CAUTION

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

6.Engage/disengage the brake and check each drive tire to make sure each brake engages/disengages.

7.If adjustment is necessary, loosen the jam nut from the yoke on the side that needs adjustment. Remove the hairpin and clevis pin (see Figure 26).

Motion Control Handle Adjustment

Adjusting the height:

The motion control levers can be adjusted higher or lower for maximum operator comfort.

1.Remove the hardware holding the control lever to the control arm shaft (Figure 27).

 

 

Figure 26

 

1.

Hairpin

3.

Yoke

2.

Clevis pin

4.

Jam nut

•Adjusting the Brake to Engage: Shorten the linkage by turning the yoke clockwise.

•Adjusting the Brake to Disengage: Lengthen the linkage by turning the yoke counterclockwise.

8.Reinstall the clevis pin and hair pin and tighten down the jam nut. Repeat step 6 and readjust if necessary.

9.When adjustment is complete, remove the jack stands or equivalent support and lower the machine.

10.Place the machine into the “operating” position. Refer to the Drive Wheel Release Valves section in Operation.

Figure 27

1.

Bolts

4.

Control arm shaft

2.

Washer

5.

Slotted hole

3.Control lever

2.Move the control lever to the next set of holes. Secure the lever with the hardware.

3.Repeat the adjustment for the opposite control lever.

Adjusting the Tilt

The motion control levers can be tilted fore or aft for maximum operator comfort.

1.Loosen the upper bolt holding the control lever to the control arm shaft.

2.Loosen the lower bolt just enough to pivot the control lever fore or aft Figure 27. Tighten both bolts to secure the control in the new position.

3.Repeat the adjustment for the opposite control lever.

Full Forward Tracking Adjustment

If the machine travels or pulls to one side when the motion control levers are in the full forward position, adjust the cover plates.

1. Loosen the screws on a cover plate (see Figure 28).

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Pioneer E-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 109-6014 116-1119 107-2102 116-1121 116-3303 116-4465 116-4430 Model Numbers SpecificationsSystems Hydrostatic Ground Drive System DimensionsTires & Wheels Cutting DeckTorque Requirements Controls Product Overview OperationMotion Control Levers Choke ControlThrottle Control Ignition Switch Fuel Shut-Off ValveBrake Lever Hour MeterDrive Wheel Release Valves PTO Engagement SwitchOperating Instructions Pre-StartDeck Lift Pedal Transport LockStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Stopping the Engine Disengaging the PTODriving the Machine Adjusting the Anti-Scalp Rollers Adjusting the Cutting HeightTransporting a Unit TransportingLoading a Unit Operation Recommended Maintenance Schedules MaintenanceRecommended Jump Starting Procedure Check Battery ChargeCheck Engine Oil Level Check Mower Blades Do Not jump start a weak battery if these conditions existService Dealer Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Knobs Service Air CleanerCheck Seat Belt Check for Loose HardwareCheck Condition Of Belts Check Tire PressuresLubricate Grease Fittings Check Spark PlugsChange Hydraulic System Filter and Fluid Service Interval After the first 100 hoursThread Locking Adhesives Check Spark Arrester if equippedCopper-Based Anti-seize Dielectric GreaseDeck Leveling Adjusting the Blade SlopePump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Full Forward Tracking Adjustment Motion Control Handle AdjustmentMotion Control Linkage Adjustment Electric Clutch Adjustment Adjusting the Seat Ride SuspensionRemove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Fins Clean Debris From MachineBattery Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Electrical Diagram SchematicsElectrical Logic Schematic Pioneer E-Series Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Top Page Image Contents