Linn Akurate Kontrol Pre-Amplifier Using the Akurate Kontrol with a Linn Akurate CD player

Page 22

ENGLISH

Installer menu

To access the Installer menu:

Press AMP, then hold SETUP on the handset, or hold SELECT on the front panel, until INSTALLER MENU is shown on the display (approximately 5 seconds).

SAVE AS INSTALLER

After you have set up the AKURATE KONTROL you can save the settings by selecting this item. The saved Installer configuration can be restored at any time should the AKURATE KONTROL’s setup be changed (see below). Any alterations to the AKURATE KONTROL’s setup that you wish to keep can be stored by selecting this item, which will overwrite the existing Installer configuration.

RESTORE INSTALLER

If you have made changes to the setup of the AKURATE KONTROL that you do not wish to keep, use this option to restore the Installer configuration.

RESTORE FACTORY

Use this option to restore the default settings for all the setup menus.

H8 SOFTWARE VERSION

Displays the version of the software installed on the AKURATE KONTROL.

Using the AKURATE KONTROL with a Linn AKURATE CD player

If an AKURATE CD is being used as a two-channel (stereo) source, simply connect the AKURATE CD’s FRONT A or B analogue line outputs to the AKURATE KONTROL’s 1/FRONT ANALOGUE AUDIO INPUTS (the AKURATE KONTROL is factory configured for an AKURATE CD to be connected to this input).

If an AKURATE CD is being used as a multi-channel source there are advantages in operation when using the AKURATE KONTROL:

The AKURATE KONTROL will choose an appropriate surround sound format for a disc’s audio stream.

When playing a CD you will be able to select the Dolby Pro Logic II surround sound format.

If you wish to use your AKURATE KONTROL with an AKURATE CD player in multi-channel configuration, follow the instructions below.

1.Switch off all equipment.

2.Connect the AKURATE CD’s FRONT A or B, SURR, CENTRE and SUB line output connectors to the 5.1 GROUP input on the AKURATE KONTROL (requires 6 RCA phono-to-phono leads)

3.Connect the RS232 product-to-product lead (supplied with the AKURATE KONTROL) from the AKURATE KONTROL’s RS232 OUT to the AKURATE CD’s RS232 IN.

4.Connect the AKURATE KONTROL’s REMOTE OUT to the AKURATE CD’s REMOTE IN (requires an RCA phono-to-phono lead).

5.Switch on all equipment.

14AKURATE KONTROL

Image 22
Contents Akurate Kontrol Page General Safety Instructions Important Safety InstructionsFor apparatus connected to the mains electricity supply Fuse replacement Mains plug replacementFCC notice CE Declaration of ConformityWaste Electrical and Electronic Equipment Weee Directive Copyright and Acknowledgements Contents Page Introduction InstallationConnecting to the mains supply UnpackingPositioning CleaningImportant information phono input Back panel SetupPower OFF, on RCUTape OUT Analogue AudioOutputs Earth GroundConnecting Setup menusSize Using the setup menusSpeaker setup Small FrequencySurround CentreSmall Surround BackSpeaker Calibration Source setupCalibration Analog GROUP, KnektType Volume OffsetName Surround ChannelsAudio setup General setup Startup Source Selection TimeoutRS232 Setup Standby Record fromLinn Disc setup Using the Akurate Kontrol with a Linn Akurate CD player Installer menuUsing the Akurate Kontrol with a Linn Unidisk player Akurate Kontrol Front panel Front Panel and HandsetFront panel display Mutes/unmutes the audio output HandsetSRC- / SRC+ source / source + Change source Operation Amp modeAdjusting the audio Standby keyTo trim loudspeaker volume Volume To change the volumeTo mute or un-mute the volume To adjust Lip Sync DelayTo change the surround sound format Surround sound formatsSurround Description Sound format Two-channel audio input Surround sound audio inputRestoring the original audio settings Midnight Movie modeTo switch Midnight Movie mode on/off Record functionSignals are downmixed to two channels Technical Specifications Linn Products Limited Guarantee and ServiceTechnical support and information Linn IncorporatedPage Pack