Exmark Lazer ZCT manual Adjustments, Cutting Height Position

Page 32

4.1.25Fuel Tank – mounting hardware specification.

When installing the nuts onto the fuel tank studs, fully tighten the nyloc nut and back off 1/2 turn. This allows for normal fuel tank expansion and contraction with changes in temperature and fuel levels.

4.1.26Thread locking adhesives such as “Loctite 242” or “Fel-Pro, Pro-Lock Nut Type” are used on the following fasteners:

a)Pump drive sheave setscrews.

b)Square head setscrews on hydro pump control arms.

c)Clutch retaining bolt in the end of engine crankshaft.

d)Caster wheel spacer nuts.

e)Fuel tank bulk head fitting nuts.

f)Cutter housing spindle nut

Adhesives such as “Loctite RC/609 or RC/680” or “Fel-ProPro-Lock Retaining I or Retaining II” are used on the following:

a)Fuel tank studs where studs are inserted into tank.

4.1.27Mobil HTS grease (or food-grade antisieze) is used in the following locations:

a)Between the cutter housing spindle and bearings.

b)Between the cutter housing spindle and sheave.

c)Under top cutter housing bearing guard.

4.1.28Dielectric grease is used on all blade type electrical connections to prevent corrosion and loss of contact.

4.2 ADJUSTMENTS

IMPORTANT: Disengage PTO, shut off engine, wait for all moving parts to stop, and remove key before servicing, cleaning or making adjustments to the unit.

4.2.1Cutting Height Adjustment.

a)Stop machine and move drive levers out to neutral lock position.

b)Disengage PTO.

c)Raise the deck lever to the transport position (also the 4.5” (11.4 cm) cutting height position). See Figure 5.

NOTE: When changing cutting height positions, always come to a complete stop and disengage the PTO.

FIGURE 5

CUTTING HEIGHT POSITION

d)Insert height adjustment pin into hole corresponding to desired cutting height and install hairpin cotter. See decal on deck lift plate.

e)Move lever out of transport (or 4.5” (11.4 cm) cutting height) position and down onto height adjustment pin to mow at selected height.

27

Page 31 Page 33
Image 32
Page 31 Page 33
Contents For Serial Nos 600,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Page Specifications Model NumberEngine Fuel SystemElectrical System Operator ControlsDimensions Hydrostatic Ground Drive SystemTires and Wheels Cutting DeckControls Operation InstructionsTorque Requirements Motion Control Positions Push the lever forward and down to disengage the brake PRE-START MowingTransporting Potential HazardMaintenance & Adjustments Periodic Maintenance Service Interval DailyService Interval Daily or more often in dry conditions Service Interval MonthlyPotential Hazard Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval Refer to chart Service Interval 40 hrService Interval 40 hrs Caster Wheel Assembly Lubrication ChartService Interval Once Yearly Service Interval 160 hrs Service Interval 80 hrsService Interval As Required Service Interval After First 250 hrs Then yearly thereafterAdjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Type a Park Brake Adjustment Type B Park Brake Adjustment Throttle TensionNo adjustment necessary RH Motion Control Adjustment LH Motion Control AdjustmentTrouble Shooting Waste DisposalEngine Troubleshooting Table ProblemBriggs & Stratton Electrical Diagram Hydraulic Diagram Year Limited Warranty Evaporative Emission Control Warranty Statement Page Page Service Record Page See EXMARK’S Complete Line of Accessories
Top Page Image Contents