Exmark TT4817KAEC, TT4817KAC, TT5217KAC, TT3615KAC, TT5217KAEC manual Specifications

Page 16

2. SPECIFICATIONS

2.1 MODEL NUMBER:

Serial Nos. 320,000 & Higher: TT3615KA; TT4817KA; TT5217KA; TT3615KAC; TT4817KAC; TT5217KAC; TT4817KAEC; TT5217KAEC

2.2ENGINE

2.2.1Engine Specifications: See your Engine Owner's Manual.

2.2.23600 RPM (No Load).

2.3FUEL SYSTEM

2.3.1Capacity: 5.0 gal.(18.9 L.)

2.3.2Type of Fuel: Regular unleaded gasoline, 87 octane or higher. In countries using the research method, it should be a 90 octane minimum.

2.3.3Fuel Filter: Replaceable in-line

2.3.4Fuel Shut-Off Valve: 1/4 turn

2.4ELECTRICAL SYSTEM (Electric start units only)

2.4.1Charging System: Flywheel Alternator

2.4.2Charging Capacity: 15 amps

2.4.3Battery Type: BCI Group U1

2.4.4Battery Voltage: 12 Volt; Polarity, negative ground

2.4.5Fuses: Two 20 amp blade type

2.5SAFETY INTERLOCK SYSTEM

Operator must have speed control lever in neutral, PTO disengaged, (and OPC levers depressed for electric start) to start engine. Release of OPC levers will cause the engine to stop if speed control lever is not in neutral and/or PTO is engaged.

2.6 STEERING CONTROL:

Fingertip drive control levers provide independent speed control, braking, and neutral to each drive wheel for moving forward or reverse, stopping, and power turning.

2.7 TRANSMISSION:

Twin Hydrostatic Drive

2.7.1Two Hydro Gear BDP-10L series variable displacement high efficiency pumps independently coupled to two high efficiency Parker/Ross wheel drive motors.

2.7.2Hydraulic Filter is replaceable cartridge type.

P/N 513211: 10 microns, 18 psi bypass (Summer use above 32° F)

P/N 523541: 40 microns, 18 psi bypass (Winter use below 32° F)

2.7.3

Speed Range:

Forward

0 - 6.2 mph (10.0 km/h)

 

 

Reverse

0 - 2.2 mph (3.5 km/h)

2.8 WHEEL DRIVE SYSTEM:

Drive wheels are direct coupled to Parker/Ross wheel drive motors with 1.0" (25.4 mm) tapered shaft.

- 11 -

Image 16
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Table of Contents Safety SpecificationsAssembly Instructions Maintenance & AdjustmentsSafety Your Safety is InvolvedSafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Page Maintenance and Storage Safety Signs Riding AttachmentsPage Page Page Specifications Dimensions TiresAssembly Instructions Torque RequirementsUpper Handle Mounting Speed Control Throttle Cable HOOK-UP Blade Engagement LinkagePage ECS Handles Drive Lever Linkage Installation Service Hydraulic OILStandard Pistol Grip Handles Operation InstructionsDrive LEVER, Neutral Lock Latch Operation Pre-Start Potential Hazard Operating Instructions Potential Hazard Transporting Maintenance & Adjustments Periodic MaintenancePotential Hazard Blade Bolt Installation Potential Hazard Service Interval After First 250 hrs, then yearly thereafter Charge Pump Location Grease Lubrication Chart Spray Lubricant ChartPage Adjustments Page Neutral Safety Switch Adjustment Hydro Drive Linkage Adjustment Hydro Control LINK/SWIVEL Adjustment Hydro Pump Spring Tension Setting Waste DisposalMotor OIL Disposal Drive Lever and Latch in Neutral PositionTrouble Shooting Battery DisposalMower Tracks to Left or Right Mower Cuts UnevenlyEngine Troubleshooting Table Engine TroubleshootingProblem Wiring Diagrams Hydraulic Diagram Warranty Limited Warranty Exmark Commercial Turf EquipmentPage Page Service Record Fold Along Appropriate Line See EXMARK’S Complete Line of Products for Turf Care ALL Rights Reserved