Exmark TT3615KAC, TT4817KAEC, TT4817KAC, TT5217KAC, TT5217KAEC manual Adjustments

Page 37

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

a)Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table below and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

IMPORTANT: Make sure the negative battery cables are disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart below for recommended charger settings).

Voltage

Percent

Maximum

 

Charging Interval

Reading

Charge

Charger Settings

 

 

 

12.6 or greater

100%

16 volts/7 amps

No Charging Required

12.4 – 12.6

75

– 100%

16 volts/7 amps

30 Minutes

12.2 – 12.4

50

– 75%

16 volts/7 amps

1

Hour

12.0 – 12.2

25

– 50%

14.4 volts/4 amps

2

Hours

11.7 – 12.0

0 – 25%

14.4 volts/4 amps

3

Hours

11.7 or less

0%

14.4 volts/2 amps

6

Hours or More

5.2ADJUSTMENTS

5.2.1Cutting height and anti-scalp roller adjustment.

WARNING

POTENTIAL HAZARD

When the two front support rod hairpins are removed from the mower deck, the weight of the tractor section may cause the front frame to rise suddenly

WHAT CAN HAPPEN

If the unit rises suddenly, injury may occur.

HOW TO AVOID THE HAZARD

Securely hold down the front of the unit when the front support rod hairpins are removed.

a)Stop engine and wait for all moving parts to stop.

b)Install hairpin clips in the holes for the desired cutting height (See Figure 11).

IMPORTANT: To maintain correct cutting height and rake, check the following for proper adjustment.

1.The front and rear hairpins are in the same holes with the proper spacers under the hair pins (See Figure 10).

2.The tire pressures are set as directed in Section 5.1.11.

3.The length of the rear deck support link assemblies are set to 6.89” (approximately 6 7/8”) from the center of the balljoint to the center of the furthest hole (See Figure 10).

- 32 -

Image 37
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Specifications Table of Contents SafetyAssembly Instructions Maintenance & AdjustmentsYour Safety is Involved SafetySafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Page Maintenance and Storage Riding Attachments Safety SignsPage Page Page Specifications Tires DimensionsTorque Requirements Assembly InstructionsUpper Handle Mounting Blade Engagement Linkage Speed Control Throttle Cable HOOK-UPPage Service Hydraulic OIL ECS Handles Drive Lever Linkage InstallationStandard Pistol Grip Handles Operation InstructionsDrive LEVER, Neutral Lock Latch Operation Pre-Start Potential Hazard Operating Instructions Potential Hazard Transporting Periodic Maintenance Maintenance & AdjustmentsPotential Hazard Blade Bolt Installation Potential Hazard Service Interval After First 250 hrs, then yearly thereafter Charge Pump Location Spray Lubricant Chart Grease Lubrication ChartPage Adjustments Page Neutral Safety Switch Adjustment Hydro Drive Linkage Adjustment Hydro Control LINK/SWIVEL Adjustment Waste Disposal Hydro Pump Spring Tension SettingMotor OIL Disposal Drive Lever and Latch in Neutral PositionBattery Disposal Trouble ShootingMower Tracks to Left or Right Mower Cuts UnevenlyEngine Troubleshooting Table Engine TroubleshootingProblem Wiring Diagrams Hydraulic Diagram Limited Warranty Exmark Commercial Turf Equipment WarrantyPage Page Service Record Fold Along Appropriate Line ALL Rights Reserved See EXMARK’S Complete Line of Products for Turf Care