Exmark 4500-355 manual Specifications, Model Numbers, Systems

Page 13

Specifications

Specifications

Model Numbers

Serial Nos: 790,000 and Higher

VH15KA362; VH15KA483; VH17KA362CA; VH17KA483CA

Systems

Engine

Engine Specifications: See your Engine Owner’s Manual

RPM: Full Speed: 3600 RPM (No Load)

Fuel System

Capacity: 5.0 gal. (18.9 L)

Type of Fuel: Regular unleaded gasoline, 87 octane or higher.

Fuel Filter: Replaceable In-line

Fuel Shut-Off Valve: 1/4 turn increments

Safety Interlock System

Operator must have the speed control lever in neutral and PTO disengaged to start engine. Release of Operator Presence Control (OPC) levers will cause engine to stop if speed control lever is not in neutral and/or PTO is engaged.

Steering/Brake Controls

Fingertip drive control levers provide independent speed control, braking and neutral to each drive wheel for moving forward or reverse, stopping and power turning.

Transmission

Two Hydro Gear variable displacement piston pumps independently coupled to two high efficiency Parker wheel drive motors.

Hydraulic Oil: Use Exmark Premium Hydro Oil.

Hydraulic Oil Capacity: 2.4 qt. (2.2 L)

Hydraulic Filter is replaceable cartridge type.

P/N 109–4180: 25 microns, 10 psi bypass (Summer use above 32°F (0°C))

P/N 1–523541: 40 microns, 18 psi bypass (Winter use below 32°F (0°C))

Speeds:

0-6.2 mph (10.0 km/hr) forward.

0-2.2 mph (3.5 km/hr) reverse.

Wheel Drive System

Drive wheels are direct coupled to Parker/Ross wheel drive motors with 1.0 inch (25.4 mm) tapered shaft.

Tires & Wheels

 

Drive

Front Caster

 

Pneumatic

Semi-

 

(Air-Filled)

Pneumatic

Quantity

2

2

Tread

Turf Master

Smooth

Size

16 x 6.50–8

9 x 3.50-4

 

 

 

Ply Rating

4

 

 

 

 

Pressure

14 psi

 

 

(97 kPa)

 

13

Image 13
Contents Viking Hydro California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 103-1798 103-2076 103-2103 103-2196 103-2242 116-0404 103-2243 103-4935 103-5626 Model Numbers SpecificationsSystems Torque Requirements DimensionsControls Product Overview OperationOperator Presence Control OPC LeversTracking Adjustment Knob Off-Run SwitchNeutral Lock Latch Park Brake LeverOperating Instructions Pre-StartStopping the Engine Disengaging the PTODriving the Machine Transporting a Unit TransportingRecommended Maintenance Schedules MaintenanceCheck Mower Blades Check Engine Oil LevelReplacing the Discharge Deflector Check for Loose Hardware Check Safety Interlock SystemChange Engine Oil Service Pre-Cleaner Element and Air CleanerCheck Hydraulic Oil Level Check Tire PressuresCheck Spark Plugs Lubricate Grease FittingsChange Fuel Filter Change Hydraulic System FilterLevel Hydraulic System Air PurgeThread Locking Adhesives Wheel Hub-Slotted Nut Torque SpecificationMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeAdjusting the Cutting Height AdjustmentsAdjusting the Axle Position Adjusting the Cutting Height with Blade Spacers Adjusting the Number of Spacers below Caster Support HubPTO Safety Switch Adjustment PTO Engagement Linkage AdjustmentInch Deck Shown for Reference Only Engine to Mower Deck Belt AdjustmentBelt Guide Adjustment Blade Brake AdjustmentPump Drive Belt Tension Adjustment Hydro Drive Linkage Adjustment Adjust Hydro Control Linkages Park Brake Adjustment Hydro Pump Spring Tension SettingRemove Engine Shrouds and Clean Cooling Fins Clean Engine Air Cooling SystemClean Grass Build-Up Under Deck Waste DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Wiring Diagram SchematicsSchematics Exmark Commercial Turf Equipment Page Page See EXMARK’S Complete Line of Accessories and Options