Ferris Industries Ferris IS1500Z Service Manual - Your Comprehensive Guide to Lawn Mower Operations

Page 19

WARNING

If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now.

Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls.

STARTING THE ENGINE

1.While sitting in the operator’s seat, engage the parking brake and make sure the PTO switch is disengaged and the motion control handles are locked in the NEUTRAL position.

2.NOTE: A warm engine may not require choking.

Set the engine throttle control to FAST throttle position. Then fully close the choke by pulling the knob OUT fully.

3.Insert the key into the ignition switch and turn it to

START.

4.After the engine starts, gradually open the choke (push knob down fully).

Warm up the engine by running it for at least a minute before engaging the PTO switch or driving the rider.

5.After warming the engine, ALWAYS operate the unit at FULL THROTTLE when mowing.

In the event of an emergency the engine can be stopped by simply turning the ignition switch to STOP. Use this method only in emergency situations. For normal engine shut down follow the procedure given in STOPPING THE RIDER.

STOPPING THE RIDER

1.Returning the ground speed control levers to the middle position will stop rider movement. Pivot the levers outward and lock them in NEUTRAL.

2.Disengage the PTO by pushing down on the PTO switch.

3.Engage the parking brake by pulling the handle up until it locks into position.

4.Move the throttle control to mid-throttle position and turn the ignition key to OFF. Remove the key.

Operation

PUSHING THE RIDER BY HAND

DO NOT TOW RIDER

Towing the unit will cause hydraulic pump and wheel motor damage. Do not use another vehicle to push or pull this unit.

1.Disengage the PTO, engage the parking brake, turn the ignition OFF, and remove the key.

2.Lift the seat plate to gain access to the hydraulic pumps.

3.To disengage the pumps (free-wheel position), turn the hydraulic release valves (A, Figure 2) located on the pumps COUNTER-CLOCKWISE a maximum of 2 full turns.

4.Disengage the parking brake.

The tractor can now be pushed by hand.

5.After moving the tractor, re-engage the pumps (drive position) by turning the release valves CLOCKWISE and tighten to 80-120 in. lbs. of torque.

A

Figure 2. Hydraulic System By-Pass

A.Hydraulic Release Valve (left-hand pump shown)

Operation

17

Image 19
Contents Model Number DescriptionFerris Industries Date Purchased Table of Contents Safety Rules & Information Operating SafetySlope Operation Roll Bar Use Fuel and Maintenance Training OperationPreparation Emissions Slope OperationTowed Equipment RIDE-ON Units ChildrenMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Operational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Identification Identification NumbersSafety Decals Safety DecalsNorth American Safety Icons Safety Interlock SystemOperational Safety Checks Control Functions Features & ControlsSeat Adjustment Lever Ignition SwitchThrottle Control PTO Power Take Off SwitchHour Meter / Maintenance Reminder Parking BrakeOperation General Operating SafetyChecks Before Starting Stopping the Rider Starting the EnginePushing the Rider by Hand Reverse Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a Corner Practice Turning In PlaceTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassProper Broadcast Mowing When and How Often to MowMowing Methods Mowing PatternsProper Mulching Attaching a TrailerKeep roll bar in the raised position and use seat belt Raise & Lower the Roll BARTo lower the roll bar To raise the roll barLong Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessCheck Tire Pressures Safety ItemsRider Maintenance Engine MaintenanceFuel Filter Regular MaintenanceEngine Maintenance Checking / Adding FuelGrease LubricationOil Change Hydraulic OIL Filter Battery MaintenanceCleaning the Battery and Cables Check Hydraulic OIL LevelRemoving the Blade Servicing the Mower BladesTroubleshooting the Rider TroubleshootingTroubleshooting the Mower Troubleshooting, Adjustment & ServiceTroubleshooting Common Cutting Problems Troubleshooting, Adjustment & ServiceGround Speed Control Lever Adjustment Seat AdjustmentSpeed Balancing Adjustment Parking Brake Adjustment Brake Spring Adjustment Nut Parking Brake AdjustmentTo adjust the spring pre-load Rear Suspension AdjustmentTo adjust the upper mounting position Blade Brake Check PTO Clutch AdjustmentNeutral Adjustment RETURN-TO-NEUTRAL AdjustmentFoot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Check Lift Rod Timing Deck Leveling AdjustmentHydraulic Pump Drive Belt Replacement Mower PTO Belt Idler Arm Stationary Idler Pulley Mower Belt ReplacementJump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryMake Certain Vehicles do not Touch This HOOK-UP for Negative Ground VehiclesChassis SpecificationsDimensions EngineFerris Limited Warranty Tractor Belts and BladesMower Deck