Husqvarna 327P5X manual General Safety Precautions, Personal protective equipment

Page 6

GENERAL SAFETY PRECAUTIONS

Important

IMPORTANT!

The machine is only designed for cutting branches and twigs.

Never use a machine that has been modified in any way from its original specification.

Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions under the heading ”Personal protective equipment”.

Never use the machine in extreme weather conditions such as severe cold, very hot and/or humid climates.

Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. See instructions under the heading Maintenance.

All covers and guards must be fitted before starting. Ensure that the spark plug cap and ignition lead are undamaged to avoid the risk of electric shock.

WARNING! This machine produces an

! electromagnetic field during operation. This field may under some circumstances interfere with active or passive medical implants. To reduce the risk of serious or fatal injury, we recommend persons with medical implants to consult their physician and the medical implant manufacturer before operating this machine.

WARNING! Running an engine in a

! confined or badly ventilated area can result in death due to asphyxiation or carbon monoxide poisoning.

WARNING! Never allow children to use or

! be in the vicinity of the machine. As the machine is equipped with a spring- loaded stop switch and can be started by low speed and force on the starter handle, even small children under some circumstances can produce the force necessary to start the machine. This can mean a risk of serious personal injury. Therefore remove the spark plug cap when the machine is not under close supervision.

Personal protective equipment

IMPORTANT!

A pole saw is a dangerous tool if used carelessly or incorrectly and can cause serious, even fatal injuries. It is extremely important that you read and understand the contents of this Operator’s Manual.

You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.

WARNING! Listen out for warning signals

! or shouts when you are wearing hearing protection. Always remove your hearing protection as soon as the engine stops.

PROTECTIVE HELMET AND VISOR

HEARING PROTECTION

Wear hearing protection that provides adequate noise reduction.

EYE PROTECTION

Blows from branches or objects that are thrown out by a cutting attachment can damage the eyes.

GLOVES

Gloves should be worn when necessary, e.g., when fitting cutting attachments.

BOOTS

Wear sturdy, non-slip boots.

6 – English

Image 6
Contents 327P4 327P5X-series KEY to Symbols SymbolsContents Introduction Dear CustomerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutStop switch Vibration damping systemMuffler Quick release Balance Flex harness Cutting equipmentSharpening your chain and adjusting raker clearance Specification of bar and saw chainChain General advice on setting raker clearance Increases the risk of kickbackSharpening cutting teeth Increased if the raker clearance is too Setting the raker clearanceTensioning the chain LargeLubricating cutting equipment Checking wear on cutting equipment Chain Chain drive sprocketMay increase the risk of accidents Fitting the cutting head AssemblyAdjusting the harness Fitting the bar and chainAssembling and dismantling the two-piece shaft AssemblyFilling with oil Fitting the impact guardAssembly of the saw attachment Fuel safety Fuel HandlingFuel Muffler gets very hot during and after FuellingMixing Use. This also applies during idling. BeStarting and stopping Starting and StoppingCheck before starting StartingStopping Working Techniques Safety instructions regarding the surroundingsSafety instructions while working General working instructionsSafety instructions after completing work Basic working techniquesWithout having the cutting attachment in full view Maintenance CarburettorMuffler Cooling system Spark plugIs damaged it should be replaced Air filter Cleaning the air filterTwo-piece shaft Oiling the air filterMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApproved accessories Art No Use with EC-declaration of conformity Applies to Europe onlyBar and chain combinations Page Page Page Page Page Original instructions 1153303-26