Husqvarna 346XPG, 353G General rules, Cutting equipment designed to reduce kickback, Bar, Chain

Page 12

GENERAL SAFETY PRECAUTIONS

•Extend the life of cutting equipment.

•Avoid increasing vibration levels.

General rules

•Only use cutting equipment recommended by us! See instructions under the heading Technical data.

•Keep the chain’s cutting teeth properly sharpened! Follow our instructions and use the recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents.

•Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. Too large a clearance increases the risk of kickback.

•Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket.

•Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to break and lead to increased wear on the bar, chain and drive sprocket.

Cutting equipment designed to reduce kickback

WARNING! Faulty cutting equipment or

! the wrong combination of bar and saw chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction and keeping the chain sharp and well- maintained you can reduce the effects of kickback.

Bar

The smaller the tip radius the lower the chance of kickback.

Chain

A chain is made up of a number of links, which are available in standard and low-kickback versions.

IMPORTANT! No saw chain design eliminates the danger of kickback.

WARNING! Any contact with a rotating

! saw chain can cause extremely serious injuries.

Some terms that describe the bar and chain

To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.

Bar

•Length (inches/cm)

•Number of teeth on bar tip sprocket (T).

•Chain pitch (inches). The spacing between the drive links of the chain must match the spacing of the teeth on the bar tip sprocket and drive sprocket.

•Number of drive links. The number of drive links is determined by the length of the bar, the chain pitch and the number of teeth on the bar tip sprocket.

12 – English

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s manual KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPAContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherStop switch Cutting equipmentRight hand guard Vibration damping systemGeneral rules Cutting equipment designed to reduce kickbackBar ChainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethIncreases the risk of kickback Sharpening cutting teethGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingTensioning the chain LargeLubricating cutting equipment When the chain touches the operator Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentAssembly Fitting the bar and chainWorking with the chain Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping RiskBasic safety rules Working TechniquesBefore use General working instructionsClutch cover causing the chain to CleaningJam. Always stop the engine before Basic cutting technique TermsLimbing Tree felling technique Logs are lying together. SuchOr fatal injury Safe distanceFelling direction Clearing the trunk and preparing your retreatTraining we advise you not to fell trees Your sawDirectional cuts Felling cutHow to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Correctly adjusted carburetor High speed jet HChecking the brake trigger Muffler Starter Changing a broken or worn starter cordTensioning the recoil spring Replacement of broken recoil and drive disc springs Air filterSpark plug Fitting the starterAdjustment of the oil pump When making adjustmentsLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature 0C 32F or colderHeated handles Electrical carburetor heatingMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gauges050/1,3 mm 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsPage Original instructions 1153178-95
Top Page Image Contents