Husqvarna 346XPG E-tech, 353G manual Assembly, Fitting the bar and chain, Working with the chain

Page 17

ASSEMBLY

Fitting the bar and chain

	!	WARNING! Always wear gloves, when
	!	working with the chain.
		working with the chain.

Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle.

Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A).

Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the groove on the bar. Begin on the top edge of the bar.

Make sure that the edges of the cutting links are facing forward on the top edge of the bar.

Fit the clutch cover and locate the chain adjuster pin in the hole in the bar. Check that the drive links of the chain ﬁt correctly over the drive sprocket and that the chain is correctly located in the groove in the bar. Tighten the bar nuts ﬁnger tight.

Tension the chain by turning the chain tensioning screw clockwise using the combination spanner. See instructions under the heading Tensioning the chain.

The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up the bar tip and tighten the bar nuts with the combination spanner.

When ﬁtting a new chain, the chain tension has to be checked frequently until the chain is run-in. Check the chain tension regularly. A correctly tensioned chain ensures good cutting performance and long life.

Note: If clutch cover is difﬁcult to remove, replace bar nuts, engage brake and rerelease (an audible click will be heard if released properly).

English – 17

Image 17

Contents Operator’s manual Symbols on the machine KEY to SymbolsEPA Symbols in the operator’s manualContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Chain catcher Throttle lockoutCutting equipment Stop switchRight hand guard Vibration damping systemCutting equipment designed to reduce kickback General rulesBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingIncreases the risk of kickback Sharpening cutting teethAdjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain LargeLubricating cutting equipment Chain drive sprocket When the chain touches the operatorNeedle bearing lubrication Checking wear on cutting equipmentWorking with the chain AssemblyFitting the bar and chain Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineRisk StoppingWorking Techniques Basic safety rulesBefore use General working instructionsJam. Always stop the engine before Clutch cover causing the chain toCleaning Limbing Basic cutting techniqueTerms Logs are lying together. Such Tree felling techniqueOr fatal injury Safe distanceClearing the trunk and preparing your retreat Felling directionTraining we advise you not to fell trees Your sawFelling cut Directional cutsFreeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburetor adjustment High speed jet H Correctly adjusted carburetorChecking the brake trigger Mufﬂer Tensioning the recoil spring StarterChanging a broken or worn starter cord Air ﬁlter Replacement of broken recoil and drive disc springsSpark plug Fitting the starterWhen making adjustments Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C 32F or colder Air Injection centrifugal cleaningHeated handles Electrical carburetor heatingDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain ﬁling and ﬁle gauges Bar and chain combinations050/1,3 mm 058/1,5 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsPage Original instructions 1153178-95