Husqvarna 346XPG, 353G, 353 E-tech Fueling, Fuel safety, Transport and storage, Long-term storage

Page 19

FUEL HANDLING

Fueling

!

WARNING! Taking the following

precautions, will lessen the risk of fire:

 

Do not smoke and do not place any hot objects in the vicinity of fuel.

Always stop the engine and let it cool for a few minutes before refuelling.

When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the refuelling area before starting.

Clean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at least once a year. Contamination in the tanks causes malfunction. Make sure the fuel is well mixed by shaking the container before refuelling.The capacities of the chain oil tank and fuel tank are carefully matched. You should therefore always fill the chain oil tank and fuel tank at the same time.

!

WARNING! Fuel and fuel vapor are highly

flammable. Take care when handling fuel

 

 

and chain oil. Be aware of the risks of

 

fire, explosion and those associated with

 

inhalation.

Fuel safety

•Never refuel the machine while the engine is running.

•Make sure there is plenty of ventilation when refuelling or mixing fuel (gasoline and 2-stroke oil).

•Move the machine at least 10 ft (3 m) from the refuelling point before starting it.

Min. 3 m (10 ft)

•Never start the machine:

1If you have spilled fuel or chain oil on the machine. Wipe off the spillage and allow remaining fuel to evaporate.

2If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water.

3If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.

!

WARNING! Never use a machine with

visible damage to the spark plug guard

 

 

and ignition cable. A risk of sparking

 

arises, which can cause a fire.

Transport and storage

•Always store the chain saw and fuel so that there is no risk of leakages or fumes coming into contact with sparks or naked flames from electrical equipment, electric motors, relays/switches, boilers and the like.

•Always store fuel in an approved container designed for that purpose.

•For longer periods of storage or for transport of the chain saw, the fuel and chain oil tanks should be emptied. Ask where you can dispose of waste fuel and chain oil at your local gas station.

•The bar guard must always be fitted to the cutting attachment when the machine is being transported or in storage, in order to prevent accident contact with the sharp chain. Even a non-moving chain can cause serious cuts to yourself or persons you bump into with an exposed chain.

•Secure the machine during transport.

Long-term storage

Empty the fuel/oil tanks in a well ventilated area. Store the fuel in approved cans in a safe place. Fit the bar guard. Clean the machine. See instructions under the heading Maintenance schedule.

Ensure the machine is cleaned and that a complete service is carried out before long-term storage.

English – 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operator’s manual Symbols on the machine KEY to SymbolsEPA Symbols in the operator’s manualContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutVibration damping system Stop switchCutting equipment Right hand guardChain General rulesCutting equipment designed to reduce kickback BarSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Increases the risk of kickbackLarge General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainLubricating cutting equipment Checking wear on cutting equipment When the chain touches the operatorChain drive sprocket Needle bearing lubricationFitting the bar and chain AssemblyWorking with the chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineRisk StoppingGeneral working instructions Basic safety rulesWorking Techniques Before useCleaning Clutch cover causing the chain toJam. Always stop the engine before Terms Basic cutting techniqueLimbing Safe distance Tree felling techniqueLogs are lying together. Such Or fatal injuryYour saw Felling directionClearing the trunk and preparing your retreat Training we advise you not to fell treesFelling cut Directional cutsWhat is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorChecking the brake trigger Muffler Changing a broken or worn starter cord StarterTensioning the recoil spring Fitting the starter Replacement of broken recoil and drive disc springsAir filter Spark plugNeedle bearing lubrication Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketElectrical carburetor heating Air Injection centrifugal cleaningTemperature 0C 32F or colder Heated handlesDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Bar and chain combinationsSaw chain filing and file gauges 050/1,3 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage Original instructions 1153178-95
Top Page Image Contents