Husqvarna 536 LIXP, 436 LI manual Battery and battery charger

Page 13

GENERAL SAFETY PRECAUTIONS

the saw chain. Third, the chain brake may be activated but if the bar is too close to you the brake might not have enough time to slow down and stop the chain before the chain saw hits you.

Only you and proper working technique can eliminate kickback and its danger.

Throttle lockout

The power trigger lockout is designed to prevent accidental operation of the power trigger. When you press the power trigger lockout (A) (i.e when you grasp the handle) it releases the power trigger (B). When you release the handle the power trigger and the power trigger lockout both move back to their original positions.

A

B

Chain catcher

The chain catcher is designed to catch the chain if it snaps or jumps off. This should not happen if the chain is properly tensioned (see instructions under the heading Assembly) and if the bar and chain are properly serviced and maintained (see instructions under the heading General working instructions).

Right hand guard

Apart from protecting your hand if the chain jumps or snaps, the right hand guard stops branches and twigs from interfering with your grip on the rear handle.

Vibrations

Cutting hardwoods (most broadleaf trees) creates more vibration than cutting softwoods (most conifers). Cutting with cutting equipment that is blunt or faulty (wrong type or badly sharpened) will increase the vibration level.

!

WARNING! Overexposure to vibration

can lead to circulatory damage or nerve

 

damage in people who have impaired

 

circulation. Contact your doctor if you

 

experience symptoms of overexposure

 

to vibration. Such symptoms include

 

numbness, loss of feeling, tingling,

 

pricking, pain, loss of strength, changes

 

in skin colour or condition. These

 

symptoms normally appear in the

 

fingers, hands or wrists. These

 

symptoms may be increased in cold

 

temperatures.

Battery and battery charger

This section describes the battery and battery charger safety for your battery product.

Only use Husqvarna original batteries for Husqvarna products and only charge them in an original battery charger from Husqvarna. The batteries are software encrypted.

Battery safety

The rechargeable Husqvarna batteries, BLi, are exclusively used as a power supply for the relevant Husqvarna cordless appliances. To avoid injury, the battery must not be used as a power source for other devices.

!

WARNING! Protect the battery from

direct sunlight, heat or open flame. There

 

 

is a risk the battery may explode if it is

 

thrown into an open fire.There is a risk of

 

burns and/or chemical burns.

English 13

Image 13
Contents 436 Li, 536 LiXP Symbols on the machine KEY to SymbolsSymbols on the battery and/or on the battery charger Symbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?General power tool safety warnings General Safety PrecautionsService Battery tool use and careChain saw safety warnings Causes and operator prevention of kickbackBefore using a new chain saw Personal protective equipment Always use common senseAutomatic switch off functionality Machine′s safety equipmentKeypad Chain brake and front hand guardGeneral Safety Precautions Battery and battery charger Cutting equipment Battery charger safetyGeneral rules Cutting equipment designed to reduce kickback General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingAdjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain Too large436 Li LiXPLubricating cutting equipment Checking chain lubrication Filling with chain oilChain drive sprocket Checking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fitting a spike bumper Battery Battery HandlingBattery charger Transport and storage Disposal of the battery, battery charger and machineLED display Charging status Starting and stopping Starting and StoppingStarting StartingStopping Working Techniques Basic safety rulesBefore use SavEGeneral rules Not safely controlled with one hand Basic cutting techniqueHandles with both hands GeneralLog is supported at both ends. There is a high risk Tree felling techniqueSafe distance Felling directionFelling Training we advise you not to fell trees Clearing the trunk and preparing your retreatYour saw Directional cutsFreeing a trapped tree Freeing a tree that has fallen badlyWhat is kickback? How to avoid kickbackCutting the trunk into logs General MaintenanceChecking the front hand guard Checking the inertia brake releasePower trigger lockout Battery connectorsLubricating the bar tip sprocket Cooling system Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleBattery Troubleshooting scheduleBattery charger Keypad Possible faults Possible actionTechnical data Technical DataSaw chain filing and file gauges EC-declaration of conformity Guide bar and saw chain combinationsApplies to Europe only Page Page 1154476-26