Husqvarna 96045000414 To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

Start tractor and release parking brake.

Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

J

K

L

FIG. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

Adjustmowertodesiredcuttingheight(See“TOADJUST MOWER CUTTING HEIGHT” in this section of manual).

Withmowerindesiredheightofcutposition,gaugewheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch.

TO STOP MOWER BLADES - disengage attachment clutch control.

S

FIG. 10

10

Image 10
Contents YTH20K46 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionMaintenance Lubrication ChartBlade Care BatteryTractor Blade Removal See FigEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH20K46 96045000414, Product no 45Electrical KEY Part Description Chassis Tractor - Model Number YTH20K46 96045000414, Product no 45 Drive Washer Harden .793 x 1.637 x Spark Arrester KIT EngineEngine Kohler Model No. SV600 Steering Assembly Tractor - Model Number YTH20K46 96045000414, Product no 45 Decals Wheels and TiresSeat Assembly 532 42 SeatMower Deck KEY Part NO. no Description Mower Lift 8787 100 101Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 42 84-01 Rev 1 05.11.09 TH

532 42 84-01, 96045000414 specifications

The Husqvarna 96045000414,532 42 84-01 is a robust riding lawn mower that exemplifies efficiency and performance in lawn care. This machine is designed for homeowners who desire a seamless mowing experience combined with ease of use and advanced technology.

One of the standout features of the Husqvarna 96045000414 is its powerful engine. It is equipped with a reliable and durable engine that ensures longevity and efficiency. This engine delivers the necessary power to tackle dense grass and tough terrains, making it suitable for various lawn sizes and conditions.

The mower's cutting deck spans 42 inches, making it ideal for residential lawns. The width ensures that it can cover a significant ground area quickly, reducing mowing time. The cutting height can be easily adjusted to suit different grass types, and the precision cutting blades guarantee a clean and even cut every time.

This model also incorporates advanced technologies that enhance the user experience. The automatic transmission allows for smooth gear shifting, making it easier to navigate different terrains without the hassle of manual adjustments. The tight turning radius provides excellent maneuverability around obstacles such as trees and flower beds.

In terms of comfort, the Husqvarna 96045000414 boasts a comfortable seat designed for extended use, reducing fatigue during longer mowing sessions. The ergonomic steering wheel and controls are intuitively placed, allowing for easy access and operation while providing optimal control over the machine.

Another attractive feature is the easy access to maintenance points, which simplifies the upkeep of the mower. Regular maintenance is crucial to maintaining performance, and Husqvarna engineers this model with user-friendly accessibility in mind.

Safety features are also a priority with the Husqvarna 96045000414. The mower comes with a safety ignition switch and an emergency brake system, ensuring that operators are safe while using the machine.

In conclusion, the Husqvarna 96045000414,532 42 84-01 riding lawn mower represents a perfect blend of power, efficiency, and comfort. With its advanced cutting technology, user-friendly features, and robust construction, it is an excellent choice for homeowners looking to maintain their lawns with ease and precision. Whether you have a small or medium-sized lawn, this model promises reliability and performance, making lawn care less of a chore and more of an enjoyable task.