TABLE OF CONTENTS
Safety Rules | Maintenance Schedule | 14 | |
Warranty | Maintenance | ||
Product Specifi cations | 8 | Service and Adjustments | |
Assembly / | 9 | Storage | |
Operation | Troubleshooting | ||
|
| Repair Parts |
SAFETY RULES
IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing ob- jects. Failure to observe the following safety instructions could result in serious injury or death.
HONDA |
|
| MODEL NUMBER | ||||
CAMSHAFT PULLEY | PISTON / CONNECTING ROD | ||||||
KEY | PART |
| KEY | PART |
| ||
NO. | NO. | DESCRIPTION | NO. | NO. | DESCRIPTION | ||
1 | Pulley, Camshaft | 1 | Piston | ||||
2 | Shaft, Cam Pulley | 2 | Pin, Piston | ||||
3 | Belt, Timing | 3 | Connecting Rod Assembly | ||||
|
|
| (84HU7 | 4 | Bolt, Connecting Rod | ||
6 | Shaft, Rocker Arm | 5 | Clip, Piston Pin (13 mm) | ||||
11 | Screw, Tappet Adjusting | 6 | Ring Set, Piston, Standard |
Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!!
YOUR SAFETY IS INVOLVED.
WARNING: In order to prevent accidental starting when setting up, transporting, ad- justing or making repairs, always disconnect spark plug wire and place wire where it cannot come in contact with plug.
WARNING: Engine exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
CAUTION: Muffl er and other engine parts become extremely
hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.
I. GENERAL OPERATION
•Read, understand, and follow all instructions on the machine and in the manual(s) before starting. Be thoroughly familiar with the controls and the proper use of the machine before starting.
•Do not put hands or feet near or under rotating parts. Keep clear of the dis- charge opening at all times.
•Only allow responsible individuals, who are familiar with the instructions, to operate the machine.
•Clear the area of objects such as rocks, toys, wire, bones, sticks, etc., which could be picked up and thrown by blade.
•Be sure the area is clear of other people before mowing. Stop the machine if anyone enters the area.
•Do not operate the mower when bare- foot or wearing open sandals. Always wear substantial foot wear.
•Do not pull mower backwards unless abso- lutely necessary.Always look down and be- hind before and while moving backwards.
•Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may richochet back toward the operator. Stop the blade when crossing gravel surfaces.
•Do not operate the mower without prop- er guards, plates, grass catcher or other safety protective devices in place.
•See manufacturer’s instructions for proper operation and installation of accessories. Only use accessories ap- proved by the manufacturer.
•Stop the blade(s) when crossing gravel drives, walks, or roads.
•Stop the engine (motor) whenever you leave the equipment, before cleaning the mower or unclogging the chute.
•Shut the engine (motor) off and wait until the blade comes to complete stop before removing grass catcher.
•Mow only in daylight or good artifi cial light.
•Do not operate the machine while under the infl uence of alcohol or drugs.
•Never operate machine in wet grass. Always be sure of your footing: keep a fi rm hold on the handle; walk, never run.
•Disengage the
•If the equipment should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibra- tion is generally a warning of trouble.
•Alwayswearsafetygogglesorsafetyglass- es with side shields when operating mower.
II. SLOPE OPERATION
Slopes are a major factor related to slip & fall accidents which can result in severe injury. All slopes require extra caution. If
2 you feel uneasy on a slope, do not mow it.
12 | Nut, Tappet Adjusting |
|
|
| (Teikoku) | ||
13 |
|
|
|
| |||
15 | Rocker Arm, Intake Valve | LABELS |
| ||||
16 | Rocker Arm, | KEY | PART |
| |||
|
|
| Exhaust Valve | NO. | NO. | DESCRIPTION | |
|
|
|
| 9 | Mark, Choke Indication | ||
OIL PAN |
| 20 | Label, Warning | ||||
KEY | PART |
| 30 | Mark, Emblem (GCV160) | |||
NO. | NO. | DESCRIPTION | 31 | Mark, Recoil Cover | |||
1 | Pan Assembly, Oil | 32 | Mark, Caution, | ||||
2 | Gauge Assembly, |
|
|
| Fuel Petcock | ||
|
|
| Oil Level |
|
|
|
|
4 | Gasket, Oil Filler Cap | CHOKE BASE |
| ||||
5 | Extension, Oil Filler | KEY | PART |
| |||
6 | Lock Washer, Extension | NO. | NO. | DESCRIPTION | |||
8 | Shaft, Governor Holder | 2 | Spring, Return | ||||
9 | Governor Assembly | 5 | Spring, Choke Lever | ||||
10 | Weight, Governor | 8 | Rod, Stop | ||||
11 | Holder, Governor Weight | 9 | Bolt, Flange (#6 x 20) | ||||
12 | Pin, Governor Weight |
|
|
| (CT200) | ||
13 | Slider, Governor | 14 | Lever Assembly, Choke | ||||
14 | Shaft, Governor Arm |
| Lever Assembly, Choke | ||||
15 | Bolt, Flange (#6 x 14) |
|
|
|
| ||
|
|
| (CT200) |
|
|
|
|
16 | Bolt, Flange (#6 x 25) |
|
|
|
| ||
|
|
| (CT200) |
|
|
|
|
17
18
19
20
21
22 | Pin, Lock (8 mm) | |
23 | Pin, Dowel (#8 x 20) |
47