Husqvarna 917.27909 owner manual To Adjust Gauge Wheels See Fig, To Operate Mower See Fig

Page 13

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position, Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface,

•Adjust mower to desired cutting height (See "TO AD- JUST MOWER CUTTING HEIGHT" in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar,

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground,

•Replace retainer spring into clevis pin,

•Be sure all gauge wheels are in the same setting,

IMPORTANT:BESURETOREADJUSTGAUGEWHEELSIFYOU CHANGETHE CUTTING HEIGHTOF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch, Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine,You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills,

 

 

LIFT LEVER

 

 

HIGHEST

 

/,

POSIITON

 

/j'

 

 

 

LOWEST

 

 

POSITION

ATTACHEMNT

 

 

CLUTCH

 

 

SWITCH PULL

 

 

OUTTO

 

 

"ENGAGE"

•.........\

 

 

j

 

PUSH IN TO

,'

DEFLECTOR

"DISENGAGE"

/

SHIELD

 

 

FIG. 10

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS), Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position,

_WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged, Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged, Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

•Depress clutch/brake pedal all the way down and hold,

•With engine running, turn ignition key counterclockwise to ROS "ON" position,

•Look down and behind before backing,

•Move gear shift lever to reverse (R) position and slowly release clutch/brake pedal to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" POSITION

ENGINE "ON" POSITION

• Select desired height of cut,

• Lower mower with attachment lift control,

•

Start mower blades by engaging attachment clutch

 

control,

•

TO STOP MOWER BLADES - disengage attachment

 

clutch control,

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

(NORMAL OPERATING)

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Husqvarna General Operation Safe Operation Practices for Ride-On MowersII. Slope Operation Safe Operation Practices ServiceIII. Children IV. Towi NGContents Unassembled Parts Carton Tools Required for AssemblyBefore Removing Tractor from Skid Unpack CartonAssemble Gauge Wheels to Mower Deck See Install Seat See FigEngage slowly Install Mower and Drive Belt SeesChecktire Pressure ChecklistCheck Deck Levelness Check for Proper Position of ALL BeltsLOW Choke Fast OperationKnow Your Tractor HOW to USE Your Tractor Using the Reverse Operation System To Adjust Gauge Wheels See FigTo Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills Before Starting the EngineTowing Carts and Other Attach Ments Check Engine OIL LevelMowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine BatteryBelts Transaxle CoolingCleaning To Install Mower Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigAdjustments ServiceTo Replace Mower Drive Belt Mower Drive Belt InstallationMower Drive Belt Removal Belt RoutingTo Adjust Attachment Clutch With Parkingbrake Engaged To Check and Adjust BrakeTo Replace Motion Drive Belt To Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbEngine OIL Fuel SystemCylinders Cause Correction PointsEngaged Problem Cause CorrectionSolenoid Optional Fuel Line SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Ground Drive Repair Parts Steering Assembly Repair Parts Spark Arrester KIT EnginePart KEYKEY Part Description Seat AssemblyKEY DecalsPart KEY Description Lift Assembly 11/32 x 1-1/2 x 10 Ga Mower Deck 183 Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationHusqvarna Warranty StatementHusqvarna

917.27909 specifications

The Husqvarna 917.27909 is a formidable riding lawn mower, designed to offer both power and versatility for homeowners who prioritize efficiency in lawn care. With a robust construction and user-friendly features, this model has garnered attention for its ability to tackle various landscaping tasks.

One of the standout features of the Husqvarna 917.27909 is its powerful engine. Equipped with a 24 horsepower Briggs & Stratton engine, it delivers reliable performance that can handle larger mowing areas without faltering. This engine offers a combination of durability and smooth operation, ensuring that even challenging terrains can be managed with ease.

The cutting deck of the Husqvarna 917.27909 measures 48 inches, allowing for an impressive cutting swath. This wide deck reduces mowing time, making it efficient for expansive yards. The deck is made of high-quality materials that resist wear and tear, and it features an adjustable cutting height to cater to varying grass lengths and user preferences.

An innovative aspect of this mower is its cutting system. The model incorporates a three-blade system that ensures a clean and even cut. This is particularly beneficial for maintaining a healthy lawn, as it prevents grass from being torn and provides a polished finish to the landscape.

User comfort is another key characteristic of the Husqvarna 917.27909. The mower is designed with an ergonomic seat and convenient controls that place essential functions at the operator's fingertips. Additionally, the steering wheel is designed for ease of use, enabling smooth maneuverability around trees and flower beds.

Technologically, the Husqvarna 917.27909 features a hydrostatic transmission, which allows for seamless speed adjustments without the need for manual gear changes. This technology enhances the overall mowing experience by providing intuitive control and the ability to navigate effortlessly across different surfaces.

For maintenance, the model includes practical features such as an easy-access deck wash port. This allows users to connect their garden hose for quick cleaning of the mowing deck, reducing the time spent on upkeep.

In summary, the Husqvarna 917.27909 is a well-engineered riding lawn mower that marries power and convenience. With its strong engine, efficient cutting deck, comfortable user experience, and innovative technology, it stands as a reliable choice for anyone looking to maintain their lawn with minimal effort and maximum results.
Top Page Image Contents