Husqvarna 917.27909 owner manual Assemble Gauge Wheels to Mower Deck See, Install Seat See Fig

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob,

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor,

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor,

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat,

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down,

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely,

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

ADJUSTMENT

KNOB

FIG. 3

NOTE: You may now roll or drive your tractor off the skid,

Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of

controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid,

TO DRIVETRACTOR OFF SKID (See Operation section for location and function of con-

trols)

_,WARNING: Before starting, read, understand and follow

all instructions in the Operation section of this manual, Be sure tractor is in a well-ventilated area, Be sure the area in

front of tractor is clear of other people and objects,

•Be sure all the above assembly steps have been com- pleted,

•Check engine oil level and fill fuel tank with gasoline.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake,

•Place gear shift lever in neutral (N) position,

•Press lift lever plunger and raise attachment lift lever to its highest position,

•Start the engine.After engine has started, move throttle control to idle position,

•Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

•Slowly release clutch/brake pedal and slowly drive tractor off skid,

•Apply brake to stop tractor, set parking brake and place gearshift lever in neutral position,

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4 and 5)

The gauge wheels are designed to keep the mower deck in proper position when operating mower,

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center Iocknuts and tighten securely.

•For ease of mower to tractor assembly, set all the gauge wheels in the fourth hole from top, Retain with clevis pins and spring retainers,

RETAINER SPRING,

PIN ----'--'--'_

SHOULDER

BOLT _ ADJUSTING

GAUGE

 

3/8-16 CENTER

3/8 WASHER

LOCKNUT

 

FIG. 4

_SETALLWHEELS

TO 4TH HOLE

FROM TOP

FIG. 5

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Husqvarna General Operation Safe Operation Practices for Ride-On MowersII. Slope Operation IV. Towi NG ServiceSafe Operation Practices III. ChildrenContents Unassembled Parts Unpack Carton Tools Required for AssemblyCarton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See Install Seat See FigEngage slowly Install Mower and Drive Belt SeesCheck for Proper Position of ALL Belts ChecklistChecktire Pressure Check Deck LevelnessLOW Choke Fast OperationKnow Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigCheck Engine OIL Level Before Starting the EngineTo Operate on Hills Towing Carts and Other Attach MentsMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Transaxle Cooling BatteryEngine BeltsCleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower HousingAdjustments ServiceBelt Routing Mower Drive Belt InstallationTo Replace Mower Drive Belt Mower Drive Belt RemovalTo Adjust Attachment Clutch With Parkingbrake Engaged To Check and Adjust BrakeTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL Fuel SystemCylinders Cause Correction PointsEngaged Problem Cause CorrectionSolenoid Optional Fuel Line SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Ground Drive Repair Parts Steering Assembly Repair Parts Spark Arrester KIT EnginePart KEYKEY Part Description Seat AssemblyKEY DecalsPart KEY Description Lift Assembly 11/32 x 1-1/2 x 10 Ga Mower Deck 183 Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationHusqvarna Warranty StatementHusqvarna

917.27909 specifications

The Husqvarna 917.27909 is a formidable riding lawn mower, designed to offer both power and versatility for homeowners who prioritize efficiency in lawn care. With a robust construction and user-friendly features, this model has garnered attention for its ability to tackle various landscaping tasks.

One of the standout features of the Husqvarna 917.27909 is its powerful engine. Equipped with a 24 horsepower Briggs & Stratton engine, it delivers reliable performance that can handle larger mowing areas without faltering. This engine offers a combination of durability and smooth operation, ensuring that even challenging terrains can be managed with ease.

The cutting deck of the Husqvarna 917.27909 measures 48 inches, allowing for an impressive cutting swath. This wide deck reduces mowing time, making it efficient for expansive yards. The deck is made of high-quality materials that resist wear and tear, and it features an adjustable cutting height to cater to varying grass lengths and user preferences.

An innovative aspect of this mower is its cutting system. The model incorporates a three-blade system that ensures a clean and even cut. This is particularly beneficial for maintaining a healthy lawn, as it prevents grass from being torn and provides a polished finish to the landscape.

User comfort is another key characteristic of the Husqvarna 917.27909. The mower is designed with an ergonomic seat and convenient controls that place essential functions at the operator's fingertips. Additionally, the steering wheel is designed for ease of use, enabling smooth maneuverability around trees and flower beds.

Technologically, the Husqvarna 917.27909 features a hydrostatic transmission, which allows for seamless speed adjustments without the need for manual gear changes. This technology enhances the overall mowing experience by providing intuitive control and the ability to navigate effortlessly across different surfaces.

For maintenance, the model includes practical features such as an easy-access deck wash port. This allows users to connect their garden hose for quick cleaning of the mowing deck, reducing the time spent on upkeep.

In summary, the Husqvarna 917.27909 is a well-engineered riding lawn mower that marries power and convenience. With its strong engine, efficient cutting deck, comfortable user experience, and innovative technology, it stands as a reliable choice for anyone looking to maintain their lawn with minimal effort and maximum results.
Top Page Image Contents