Husqvarna 345e EPA II, 346XP EPA I, 353 EPA II manual Lubricating cutting equipment, Chain oil

Page 14

GENERAL SAFETY PRECAUTIONS

Tighten the bar clutch by turning the knob clockwise.

Fold the knob back in to lock the tensioning.

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

!equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which has a vegetable oil base. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

Filling with chain oil

All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel), and that you adjust the carburetor as recommended (a lean mixture may mean that the fuel lasts longer than the oil) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil).

Checking chain lubrication

Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket.

Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

Check that the oil channel in the bar is not obstructed. Clean if necessary.

Check that the groove in the edge of the bar is clean. Clean if necessary.

14 – English

Image 14
Contents TrioBrake Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackSharpening cutting teeth General advice on adjusting depth gauge settingAdjustment of depth gauge setting 345e TrioBrake Tensioning the chain346XP TrioBrake, 353 TrioBrake Filling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication 346XP TrioBrake, 353 TrioBrake AssemblyFitting the bar and chain 345e TrioBrakeAssembly Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Terms Basic cutting techniqueGeneral Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Correctly adjusted carburetor High speed jet HChecking the brake trigger Changing a broken or worn starter cord MufflerStarter Fitting the starter Replacement of broken recoil and drive disc springsTensioning the recoil spring Lubricating the bar tip sprocket Air filterSpark plug Needle bearing lubricationCooling system Adjustment of the oil pumpAir Injection centrifugal cleaning Heated handlesTemperature 0C 32F or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage 1150389-95 ´z+RF¶5&¨ ´z+RF¶5&¨

345e EPA II, 346XP EPA I, 353 EPA II specifications

Husqvarna is a renowned name in outdoor power equipment, and its chainsaws exemplify performance, durability, and advanced technology. Among their impressive lineup, the Husqvarna 345e EPA II, 346XP EPA I, and 353 EPA II stand out due to their unique features and capabilities tailored for both professional and casual users.

The Husqvarna 345e EPA II is designed for optimal power-to-weight ratio, making it a favorite for professionals who need mobility without sacrificing performance. This model is powered by a 50.1 cc engine that delivers a robust 3.2 horsepower, providing ample power for demanding cutting tasks. The 345e features a lightweight design, which reduces fatigue during extended use. It also incorporates the X-Torq engine technology, which reduces fuel consumption and emissions, ensuring compliance with EPA regulations. Additionally, the chainsaw comes equipped with an inertia-activated chain brake for enhanced safety and a tool-less chain tensioning system for quick adjustments.

Next is the Husqvarna 346XP EPA I, a top choice for professional loggers and tree care specialists. This chainsaw features a 50.1 cc engine as well, but its unique design focuses on high performance and exceptional ergonomics. The 346XP is renowned for its rapid acceleration and high chain speed, which allow it to tackle tough cutting jobs with ease. Its Air Injection technology separates larger dust and debris, ensuring the air filter remains clean for longer periods, thereby reducing maintenance. This model is also equipped with the LowVib system that minimizes vibrations, enhancing user comfort during prolonged use.

Finally, the Husqvarna 353 EPA II is tailored for those seeking a middle ground between professional and casual use. This chainsaw features a 49.5 cc engine and balances power with user-friendly features. It is equipped with the same X-Torq engine technology found in the 345e, ensuring efficient fuel consumption and lower emissions. The 353 also boasts a well-designed handle for improved grip and control, making it ideal for various cutting tasks from firewood to felling trees. Its quick-release air filter makes maintenance straightforward, allowing users to focus more on their work.

Together, the Husqvarna 345e EPA II, 346XP EPA I, and 353 EPA II represent a blend of cutting-edge technology and user-oriented design, delivering reliability and performance, whether for professional use or home maintenance. Each model offers unique strengths, ensuring there is a perfect fit for every chainsaw user’s needs.