Husqvarna 345e EPA II, 346XP EPA I, 353 EPA II Tensioning the recoil spring, Fitting the starter

Page 34

MAINTENANCE

345e:

•Undo the bolt in the centre of the pulley and remove the drive disc, drive disc spring and the pulley. Insert and secure a new starter cord in the starter pulley. Wind approx. 3 turns of the starter cord on the starter pulley. Fit the starter pulley so that the end of the recoil spring hooks into the starter pulley. Now assemble the drive disc spring, drive disc and the bolt in the centre of the pulley. Carry the starter cord through the hole in the starter housing and the starter handle. Tie a good knot on the starter cord.

346XP, 353:

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley.

Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the center of the pulley. Insert the starter cord through the hole in the starter housing and the starter handle. Make a secure knot in the end of the starter cord.

Tensioning the recoil spring

•Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned an additional 1/ 2 turn when the starter cord is pulled all the way out.

Replacement of broken recoil and drive disc springs

Recoil spring (A)

•Lift up the starter pulley. See instructions under the heading Changing a broken or worn starter cord. Remember that the recoil spring is coiled under tension in the starter housing.

•Remove the cassette with the recoil spring from the starter.

•Lubricate the recoil spring with light oil. Fit the cassette with recoil spring in the starter. Fit the starter pulley and tension the recoil spring.

Drive disc spring (B)

345e:

•Undo the bolt in the centre of the pulley and remove the drive disc and the drive disc spring.

•Replace the drive disc spring and fit the drive disc above the spring.

A

A

B

345e

346XP, 353

Fitting the starter

•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

34 – English

Page 33 Page 35
Image 34
Page 33 Page 35
Contents TrioBrake Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackAdjustment of depth gauge setting General advice on adjusting depth gauge settingSharpening cutting teeth 346XP TrioBrake, 353 TrioBrake Tensioning the chain345e TrioBrake Filling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment 346XP TrioBrake, 353 TrioBrake AssemblyFitting the bar and chain 345e TrioBrakeAssembly Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules General Basic cutting techniqueTerms Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Correctly adjusted carburetor High speed jet HChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Replacement of broken recoil and drive disc springsFitting the starter Lubricating the bar tip sprocket Air filterSpark plug Needle bearing lubricationCooling system Adjustment of the oil pumpAir Injection centrifugal cleaning Heated handlesTemperature 0C 32F or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage 1150389-95 ´z+RF¶5&¨ ´z+RF¶5&¨
Top Page Image Contents