Husqvarna 345e EPA II, 346XP EPA I, 353 EPA II manual Maintenance, General, Carburetor adjustment

Page 30

MAINTENANCE

General

The user must only carry out the maintenance and service work described in this manual.

IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer (retailer).

Carburetor adjustment

Due to existing environmental and emissions legislation your chain saw is equipped with movement limiters on the carburetor adjuster screws. These limit the adjustment possibilities to a maximum of a 1/2 turn.

1/2

1/2

Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions.

Function

•The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. The air/ fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine.

•The satisfactory operation of a catalytic converter depends, among other factors, on the correct adjustment of the carburetor. Carefully follow the instructions below, using a tachometer as an aid.

•The setting of the carburetor means that the engine is adapted to local conditions, for example, the climate, altitude, fuel and the type of 2-stroke oil.

•The carburetor has three adjustment controls:

-L = Low speed jet

-H = High speed jet

-T = Idle adjustment screw

LH

T

•The L and H-jets are used to adjust the supply of fuel to match the rate that air is admitted, which is controlled with the throttle. If they are screwed clockwise the air/fuel ratio becomes leaner (less fuel) and if they are turned anti- clockwise the ratio becomes richer (more fuel). A lean mixture gives a higher engine speed and a rich mixture gives a lower engine speed.

•The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.

Basic settings and running in

The basic carburetor settings are adjusted during testing at the factory. Avoid running at a too high speed for extended periods during the first 10 hours.

CAUTION! If the chain rotates while idling the T-screw must be turned anti-clockwise until the chain stops.

Rec. idle speed: 2700 rpm

Fine adjustment

When the machine has been ”run-in” the carburetor should be finely adjusted. The fine adjustment should be carried out by a qualified person. First adjust the L-jet, then the idling screw T and then the H-jet.

Conditions

•Before any adjustments are made the air filter should be clean and the cylinder cover fitted. Adjusting the carburetor while a dirty air filter is in use will result in a leaner mixture next time the filter is cleaned. This can give rise to serious engine damage.

•Do not attempt to adjust the L and H jets beyond either stop as this could cause damage.

•Now start the machine according to the starting instructions and let it warm up for 10 minutes.

•Place the machine on a flat surface so that the bar points away from you and so that the bar and chain do not come into contact with the surface or other objects.

Low speed jet L

Turn the low speed jet L clockwise until it stops. If the engine accelerates poorly or idles unevenly, turn the low speed jet L anticlockwise until good acceleration and idling are achieved.

Fine adjustment of the idling speed T

Adjust the idle speed with the T-screw. If it is necessary to re- adjust, turn the T-screw clockwise while the engine is running, until the chain starts to rotate. Then turn counter-clockwise until the chain stops. A correctly adjusted idle speed setting occurs when the engine runs smoothly in every position. It should also be good margin to the rpm when the chain starts to rotate.

WARNING! Contact your servicing dealer, if

!the idle speed setting cannot be adjusted so that the chain stops at idle. Do not use the chain saw until it has been properly adjusted or repaired.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents TrioBrake KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingSharpening cutting teeth Tensioning the chain 346XP TrioBrake, 353 TrioBrake345e TrioBrake Filling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment 346XP TrioBrake, 353 TrioBrake AssemblyFitting the bar and chain 345e TrioBrakeAssembly Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique GeneralTerms Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Correctly adjusted carburetor High speed jet HChecking the brake trigger Muffler StarterChanging a broken or worn starter cord Replacement of broken recoil and drive disc springs Tensioning the recoil springFitting the starter Lubricating the bar tip sprocket Air filterSpark plug Needle bearing lubricationCooling system Adjustment of the oil pumpAir Injection centrifugal cleaning Heated handlesTemperature 0C 32F or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage 1150389-95 ´z+RF¶5&¨ ´z+RF¶5&¨

345e EPA II, 346XP EPA I, 353 EPA II specifications

Husqvarna is a renowned name in outdoor power equipment, and its chainsaws exemplify performance, durability, and advanced technology. Among their impressive lineup, the Husqvarna 345e EPA II, 346XP EPA I, and 353 EPA II stand out due to their unique features and capabilities tailored for both professional and casual users.

The Husqvarna 345e EPA II is designed for optimal power-to-weight ratio, making it a favorite for professionals who need mobility without sacrificing performance. This model is powered by a 50.1 cc engine that delivers a robust 3.2 horsepower, providing ample power for demanding cutting tasks. The 345e features a lightweight design, which reduces fatigue during extended use. It also incorporates the X-Torq engine technology, which reduces fuel consumption and emissions, ensuring compliance with EPA regulations. Additionally, the chainsaw comes equipped with an inertia-activated chain brake for enhanced safety and a tool-less chain tensioning system for quick adjustments.

Next is the Husqvarna 346XP EPA I, a top choice for professional loggers and tree care specialists. This chainsaw features a 50.1 cc engine as well, but its unique design focuses on high performance and exceptional ergonomics. The 346XP is renowned for its rapid acceleration and high chain speed, which allow it to tackle tough cutting jobs with ease. Its Air Injection technology separates larger dust and debris, ensuring the air filter remains clean for longer periods, thereby reducing maintenance. This model is also equipped with the LowVib system that minimizes vibrations, enhancing user comfort during prolonged use.

Finally, the Husqvarna 353 EPA II is tailored for those seeking a middle ground between professional and casual use. This chainsaw features a 49.5 cc engine and balances power with user-friendly features. It is equipped with the same X-Torq engine technology found in the 345e, ensuring efficient fuel consumption and lower emissions. The 353 also boasts a well-designed handle for improved grip and control, making it ideal for various cutting tasks from firewood to felling trees. Its quick-release air filter makes maintenance straightforward, allowing users to focus more on their work.

Together, the Husqvarna 345e EPA II, 346XP EPA I, and 353 EPA II represent a blend of cutting-edge technology and user-oriented design, delivering reliability and performance, whether for professional use or home maintenance. Each model offers unique strengths, ensuring there is a perfect fit for every chainsaw user’s needs.
Top Page Image Contents