Husqvarna 345e EPA II, 346XP EPA I, 353 EPA II manual Muffler, Starter

Page 33

MAINTENANCE

Vibration damping system

Regularly check the vibration damping units for cracks or deformation.

Make sure the vibration damping units are securely attached to the engine unit and handle unit.

Stop switch

Start the engine and make sure the engine stops when you move the stop switch to the stop setting.

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine.

Some mufflers are equipped with a special spark arrestor screen. If your machine has this type of muffler, you should clean the screen at least once a week. This is best done with a wire brush. A blocked screen will cause the engine to overheat and may lead to serious damage.

Note! The screen must be replaced if it is damaged. If the screen is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition. Never use a muffler if the spark arrestor screen is missing or defective.

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator.The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

A muffler equipped with a catalytic converter significantly reduces the amount of hydrocarbons (HC), nitrogen oxides (NO) and aldehydes in the exhaust fumes. Carbon monoxide (CO), which is poisonous and odorless, is not however reduced! Consequently, never work in an enclosed or badly ventilated area. Good air circulation should always prevail when working in snowy hollows, ravines or in confined conditions.

Starter

WARNING! When the recoil spring is wound

!up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring, starter cord or the drive disc spring. Wear protective glasses and protective gloves.

Changing a broken or worn starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter.

•Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

English – 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents TrioBrake KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping systemCutting equipment Stop switchMuffler General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingSharpening cutting teeth Tensioning the chain 346XP TrioBrake, 353 TrioBrake345e TrioBrake Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Fitting the bar and chain Assembly346XP TrioBrake, 353 TrioBrake 345e TrioBrakeAssembly Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Basic cutting technique GeneralTerms Cutting LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral High speed jet H Correctly adjusted carburetorChecking the brake trigger Muffler StarterChanging a broken or worn starter cord Replacement of broken recoil and drive disc springs Tensioning the recoil springFitting the starter Spark plug Air filterLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Adjustment of the oil pumpCooling system Heated handlesTemperature 0C 32F or colder Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsPage 1150389-95 ´z+RF¶5&¨ ´z+RF¶5&¨

345e EPA II, 346XP EPA I, 353 EPA II specifications

Husqvarna is a renowned name in outdoor power equipment, and its chainsaws exemplify performance, durability, and advanced technology. Among their impressive lineup, the Husqvarna 345e EPA II, 346XP EPA I, and 353 EPA II stand out due to their unique features and capabilities tailored for both professional and casual users.

The Husqvarna 345e EPA II is designed for optimal power-to-weight ratio, making it a favorite for professionals who need mobility without sacrificing performance. This model is powered by a 50.1 cc engine that delivers a robust 3.2 horsepower, providing ample power for demanding cutting tasks. The 345e features a lightweight design, which reduces fatigue during extended use. It also incorporates the X-Torq engine technology, which reduces fuel consumption and emissions, ensuring compliance with EPA regulations. Additionally, the chainsaw comes equipped with an inertia-activated chain brake for enhanced safety and a tool-less chain tensioning system for quick adjustments.

Next is the Husqvarna 346XP EPA I, a top choice for professional loggers and tree care specialists. This chainsaw features a 50.1 cc engine as well, but its unique design focuses on high performance and exceptional ergonomics. The 346XP is renowned for its rapid acceleration and high chain speed, which allow it to tackle tough cutting jobs with ease. Its Air Injection technology separates larger dust and debris, ensuring the air filter remains clean for longer periods, thereby reducing maintenance. This model is also equipped with the LowVib system that minimizes vibrations, enhancing user comfort during prolonged use.

Finally, the Husqvarna 353 EPA II is tailored for those seeking a middle ground between professional and casual use. This chainsaw features a 49.5 cc engine and balances power with user-friendly features. It is equipped with the same X-Torq engine technology found in the 345e, ensuring efficient fuel consumption and lower emissions. The 353 also boasts a well-designed handle for improved grip and control, making it ideal for various cutting tasks from firewood to felling trees. Its quick-release air filter makes maintenance straightforward, allowing users to focus more on their work.

Together, the Husqvarna 345e EPA II, 346XP EPA I, and 353 EPA II represent a blend of cutting-edge technology and user-oriented design, delivering reliability and performance, whether for professional use or home maintenance. Each model offers unique strengths, ensuring there is a perfect fit for every chainsaw user’s needs.
Top Page Image Contents