Husqvarna 345e EPA II, 346XP EPA I, 353 EPA II Air filter, Spark plug, Needle bearing lubrication

Page 35

MAINTENANCE

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week).

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates.

English – 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents TrioBrake Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth General advice on adjusting depth gauge settingAdjustment of depth gauge setting 345e TrioBrake Tensioning the chain346XP TrioBrake, 353 TrioBrake Checking chain lubrication Lubricating cutting equipmentChain oil Filling with chain oilChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication 345e TrioBrake AssemblyFitting the bar and chain 346XP TrioBrake, 353 TrioBrakeAssembly Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueGeneral Cutting LimbingClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionDirectional cuts FellingCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment High speed jet H Correctly adjusted carburetorChecking the brake trigger Changing a broken or worn starter cord MufflerStarter Fitting the starter Replacement of broken recoil and drive disc springsTensioning the recoil spring Needle bearing lubrication Air filterSpark plug Lubricating the bar tip sprocketHeated handles Adjustment of the oil pumpAir Injection centrifugal cleaning Cooling systemTemperature 0C 32F or colder Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage 1150389-95 ´z+RF¶5&¨ ´z+RF¶5&¨

345e EPA II, 346XP EPA I, 353 EPA II specifications

Husqvarna is a renowned name in outdoor power equipment, and its chainsaws exemplify performance, durability, and advanced technology. Among their impressive lineup, the Husqvarna 345e EPA II, 346XP EPA I, and 353 EPA II stand out due to their unique features and capabilities tailored for both professional and casual users.

The Husqvarna 345e EPA II is designed for optimal power-to-weight ratio, making it a favorite for professionals who need mobility without sacrificing performance. This model is powered by a 50.1 cc engine that delivers a robust 3.2 horsepower, providing ample power for demanding cutting tasks. The 345e features a lightweight design, which reduces fatigue during extended use. It also incorporates the X-Torq engine technology, which reduces fuel consumption and emissions, ensuring compliance with EPA regulations. Additionally, the chainsaw comes equipped with an inertia-activated chain brake for enhanced safety and a tool-less chain tensioning system for quick adjustments.

Next is the Husqvarna 346XP EPA I, a top choice for professional loggers and tree care specialists. This chainsaw features a 50.1 cc engine as well, but its unique design focuses on high performance and exceptional ergonomics. The 346XP is renowned for its rapid acceleration and high chain speed, which allow it to tackle tough cutting jobs with ease. Its Air Injection technology separates larger dust and debris, ensuring the air filter remains clean for longer periods, thereby reducing maintenance. This model is also equipped with the LowVib system that minimizes vibrations, enhancing user comfort during prolonged use.

Finally, the Husqvarna 353 EPA II is tailored for those seeking a middle ground between professional and casual use. This chainsaw features a 49.5 cc engine and balances power with user-friendly features. It is equipped with the same X-Torq engine technology found in the 345e, ensuring efficient fuel consumption and lower emissions. The 353 also boasts a well-designed handle for improved grip and control, making it ideal for various cutting tasks from firewood to felling trees. Its quick-release air filter makes maintenance straightforward, allowing users to focus more on their work.

Together, the Husqvarna 345e EPA II, 346XP EPA I, and 353 EPA II represent a blend of cutting-edge technology and user-oriented design, delivering reliability and performance, whether for professional use or home maintenance. Each model offers unique strengths, ensuring there is a perfect fit for every chainsaw user’s needs.
Top Page Image Contents