Husqvarna 345e EPA II, 346XP EPA I, 353 EPA II manual Tensioning the chain, 345e TrioBrake

Page 13

GENERAL SAFETY PRECAUTIONS

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the ﬂat ﬁle to ﬁle off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the ﬁle along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off the

!bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

346XP TrioBrake, 353 TrioBrake

•Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to ﬁnd out where it is on your model.

345e TrioBrake

•Release the knob by folding it out.

•Turn the knob anti clockwise to loosen the bar cover.

•Adjust the tension on the chain by turning the wheel down

(+) for tighter tension and up (-) to loosen the tension.

English – 13

Image 13

Contents TrioBrake Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping system Cutting equipment Stop switch Mufﬂer General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingAdjustment of depth gauge setting General advice on adjusting depth gauge settingSharpening cutting teeth 346XP TrioBrake, 353 TrioBrake Tensioning the chain345e TrioBrake Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain Assembly346XP TrioBrake, 353 TrioBrake 345e TrioBrakeAssembly Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms Cutting LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorChecking the brake trigger Starter MufﬂerChanging a broken or worn starter cord Tensioning the recoil spring Replacement of broken recoil and drive disc springsFitting the starter Spark plug Air ﬁlterLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Adjustment of the oil pumpCooling system Heated handlesTemperature 0C 32F or colder Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain ﬁling and ﬁle gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsPage 1150389-95 ´z+RF¶5&¨ ´z+RF¶5&¨