Husqvarna RZ3019 BF/966582101, RZ3016 CA/966612302, RZ3016/966612301 Maintenance Schedule

Page 33

MAINTENANCE

Maintenance Schedule

The following is a list of maintenance procedures that must be performed on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by

an authorized service workshop is recommended to maintain your machine in the best possible condition and to ensure safe operation.

Read Maintenance in the Safety section.

 

 

Daily

At least

Maintenance interval

 

Maintenance

once

 

in hours

 

 

 

 

each

 

 

 

 

 

 

 

Before

After

25

50

 

100

300

 

 

year

 

 

 

 

 

 

 

 

 

 

Check the parking brake

 

 

 

 

 

 

 

Check the engine’s oil level (every refueling)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Check the safety system

 

 

 

 

 

 

 

Check for fuel and oil leakages

 

 

 

 

 

 

 

Check/clean the engine’s cooling air intake

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Check the mower deck

 

 

 

 

 

 

 

Check for loose hardware (screws, nuts)

 

 

 

 

 

 

 

Clean under the mower deck

 

 

 

 

 

 

 

Start the engine and blades, listen for unusual sounds

 

 

 

 

 

 

 

Check for damage

 

 

 

 

 

 

 

Thoroughly clean around the engine

 

 

 

 

 

 

 

Clean around belts, belt pulleys

 

 

 

 

 

 

 

Check the tire pressures

 

 

 

 

 

 

 

Check battery

 

 

 

 

 

 

 

Sharpen/replace mower blades

 

 

 

 

 

 

 

Clean the engine’s cooling air intake 2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clean the air cleaner’s foam pre-filter 2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clean the air cleaner’s paper filter cartridge 2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Check/adjust the parking brake

 

 

 

 

 

 

1)

First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace

 

 

 

 

 

 

every 50 hours.

 

 

 

 

 

 

 

 

2)

In dusty conditions, cleaning and replacement are required more often.

 

 

 

 

 

 

 

 

 

 

 

 

 

3)

For daily use, the machine should be lubricated twice weekly.

 

 

 

 

 

 

 

 

 

 

 

 

 

4)

Performed by authorized service workshop.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

= Described in this manual

 

 

 

 

 

 

 

 

= Not described in this manual

 

 

 

 

 

 

 

 

= See engine manufacturers’ Owners Manual

 

 

 

 

 

 

 

 

33

Image 33
Contents Operator Manual All rights reserved Contents Page Introduction Manufacturing Number Good ServiceXxxx xxxxxx xxxxx xxxx Xxxxxx xxxxxxxxx. xx xxxxxxxx Symbols and DecalsRemove key before Safety Safety InstructionsGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentBe extra cautious when driving on slopes Safe Handling of Gasoline General Maintenance Risk of sparking Spark Arrestor TransportControl Locations ControlsSteering Control Levers Ignition Switch Parking BrakeThrottle Control Refueling Choke ControlMower Deck Lifting Lever Fuel Shut Off ValveTracking Always use the high position F to transportBypass Linkages Blade Control LeverOperation TrainingSteering Starting the Engine Before StartingPlace controls in neutral position Open the fuel valve To remove cables, reverse order Jumper cablesRunning Operating on Hills Mowing Tips Stopping the Engine Moving Machine By Hand Maintenance Schedule Maintenance100 300 Year Battery Cleaning battery and terminalsAlways use protective glasses when handling the battery Tire Pressures Safety SystemBelts Deck BeltTo replace deck belt Cutting Blades EZT BeltLeveling Deck Adjusting the Mower DeckRemoval and installation of caster wheel CleaningUse protective glasses when cleaning and washing Caster WheelsGeneral LubricationFront Wheel Bearings Front Wheel MountDeck Spindle TransmissionProblem Cause TroubleshootingTroubleshooting Service StorageWinter Storage Schematic Technical Data Torque SpecificationsStandard Hardware Transmission 966582101 966612301 EngineOverall dimensions 966582101 966612301 EquipmentProductivity USA Requirements Conformity CertificatesDelivery Service Service JournalAfter 5-10 Hours Hour ServicePerform the 25-hour service At Least Once Each Year Page 115 383627 Rev E 2012-06-30