Husqvarna Rider 15V2 manual Storage, Winter storage, Cover, Service

Page 47

STORAGE

Winter storage

At the end of the season the machine should immediately be put in order for storage, also if it is going to stand idle for more than 30 days. Fuel which is left to stand for long periods (30 days or more) can leave tacky deposits which can block the carburettor and interfere with the engine.

Fuel stabiliser is an acceptable alternative to avoid tacky deposits during storage. Add stabiliser to the fuel in the tank or the storage container. Always use the mixing ratios indicated by the manufacturer. Run the engine for at least 10 minutes after adding the stabiliser so that it will reach the carburettor. Do not empty the fuel tank and carburettor if stabiliser has been added.

WARNING!

Never place an engine with fuel in the tank indoors or in poorly ventilated areas where petrol fumes can come into contact with naked flames, sparks or pilot flames in boilers, hot water heaters, or drying cabinets, etc. It is highly inflammable and negligent usage can cause severe person injury and material damage. Drain off the fuel in an approved container outdoors and well clear of naked flames. Never use petrol for cleaning purposes. Use degreasing agents and hot water instead.

To put the machine in order for storage, follow these instructions:

1.Carefully clean the machine, especially under the cutting unit. Touch-up paint damage to avoid rust.

2.Inspect the machine for worn or damaged parts and tighten loose screws and nuts.

3.Change the oil, and take care of the waste oil.

4.Empty the fuel tank. Start the engine and run it until the carburettor is emptied of fuel.

5.Remove the spark plugs and pour about a tablespoon of engine oil in each cylinder. Turn over the engine so that the oil is evenly distributed and then refit the spark plugs.

6.Grease all grease nipples, joints and axles.

7.Remove the battery. Clean it, charge it, and store it in a cool place.

8.Store the machine in a clean and dry place and cover it over for extra protection.

Cover

There is a cover to protect your machine during storage or transport. Contact your dealer for a demonstration.

Service

When ordering spare parts, always state the purchase year, model, type, and serial number.

Always use genuine parts.

Annual inspection or trimming by an authorised service workshop is a good way of getting the best out of your machine the next season.

6017-213

English – 45

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Rider Svenska Contents III. Children Safe operation practices for ride-on mowersGeneral operation II. Slope operationIntended use IV. ServiceTravel and transport on public roads TowingTowing IntroductionDear customer Travel and transport on public roadsSerial number Good serviceStarting Instruction Explanation of SymbolsGeneral use Safety InstructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Parking brake Throttle controlChoke lever Speed limiterLift lever for cutting unit Cutting unitFuelling Lever for adjustment of cutting heightSeat Starting the engine DrivingBefore starting 6017-244 6017-245 Driving the machine Cutting tips Release lever Stopping the engineHours Before start 100 200 MaintenanceMaintenance schedule Daily Maintenance intervalRight-hand fender Removing the machine hoodsEngine hood Front hoodPoorly adjusted brakes can result in reduced braking power Checking and adjustment of the steering wiresAdjusting the brake Replacing the fuel filter Checking and adjustment of the throttle wireChecking and adjusting the choke wire Varning Replacing the air filterFitting the wrong spark plug type can damage the engine Check the level of the battery acidChecking of the fuel pump’s air filter Inspecting the safety system Checking the engine’s cooling air intake Main fuseChecking the tyre pressure Observe caution to avoid trapping your hand Fitting the cutting unitRemoving the cutting unit Checking and adjusting the cutting unit’s ground pressure Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitBelt change on Combi Replacing the cutting unit beltsBelt change on cutting unit with side ejection and Combi Placing in service position Service position for the cutting unit6017-221 6017-222 8009-122 6017-223 Restoring from service position Checking the blades Removal of BioClip plug Combi Replacing the break-pin CombiChecking the engine’s oil level LubricationChanging the oil filter Changing the oilGeneral lubrication Lubricating the belt adjusterChecking the transmission’s oil level Problem Procedure Trouble Shooting ScheduleCover ServiceStorage Winter storageTechnical Data Work done Service JournalPre-delivery service Work done Date, mileage, stamp, sign Service Journal Service Journal ´z+H-¶5O¨ Page 114 01

Rider 15V2 specifications

The Husqvarna Rider 15V2 is a remarkable piece of gardening machinery that represents the pinnacle of innovation in compact, versatile riding mowers. Designed for both homeowners and professional landscapers, this model combines efficiency and precision in lawn care.

One of the standout features of the Rider 15V2 is its unique articulated steering system. This technology allows the rear wheels to follow the front wheels, which significantly enhances maneuverability. Gardeners can easily navigate around tight corners, flower beds, and obstacles without damaging the lawn. This feature is especially useful in landscaped gardens where navigating narrow pathways is often a challenge.

Equipped with a powerful 15 horsepower engine, the Rider 15V2 delivers robust performance, ensuring that it can tackle various types of terrain and vegetation. The engine is coupled with a hydrostatic transmission, providing seamless speed control without the need for shifting gears. This offers a more comfortable driving experience and reduces operator fatigue during extended mowing sessions.

The cutting deck of the Rider 15V2 can be easily adjusted to multiple cutting heights, ranging from 25 mm to 75 mm, which allows users to customize the cut according to their preference and grass type. This flexibility is essential for those who desire a well-manicured lawn throughout the mowing season. The deck's unique design also enables excellent grass collection and reduces clumping in various grass conditions.

Another notable characteristic is its compact size, making it easier to store than traditional riding mowers. Despite its smaller footprint, Husqvarna has engineered the Rider 15V2 to deliver exceptional cutting width, ensuring efficient coverage of larger areas without frequent turns or passes.

Additionally, the Rider 15V2 is equipped with intuitive controls that ensure ease of use for operators of all skill levels. The ergonomic seat and ergonomic steering wheel contribute to operator comfort, allowing for prolonged use without discomfort.

Overall, the Husqvarna Rider 15V2 is a powerful and innovative riding mower that merges advanced technology with practical design. Whether for residential or commercial purposes, it provides exceptional performance, unmatched maneuverability, and user-friendly features that make lawn care a breeze. With Husqvarna's commitment to quality and durability, this mower is built to last, ensuring reliable service for years to come.
Top Page Image Contents