Husqvarna 240440 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

5/16" wrench

Utility knife

(2)

7/16" wrenches

Tire pressure gauge

(2)

1/2" wrenches

Pliers

(1)

9/16" wrench

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKIDTHAT MAY PUNCTURETIRES WHERE TRACTOR IS TO ROLL OFF SKID.

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

"."-.....

"" .............WHEEL

LOWER

STEERING

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

•Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

•For battery and battery cable installation see "RE- PLACING BATTERY"in the "Service and Adjustments" section in this manual.

LABEL

Fig. 2

INSTALL SEAT (See Figs. 3 and 4)

•Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Remove the cardboard packing and discard.

•Connect switch to seat.

•Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

/

SEAT/

Fig. 1

TO INSTALL STEERING WHEEL (See Fig. 2)

•Remove Iocknut and large flat washer from steering

 

shaft.

/

_J

•

Position front wheels of the tractor so they are pointing

 

/

 

/

 

straight forward.

 

 

 

TAPE

•Position steering wheel so cross bars are horizontal

(left to right) and slide onto steering wheel adapter.

WIRING HARNESS

•Secure steering wheel to steering shaft with Iocknut

and large flat washer previously removed. Tighten

Fig. 3

securely.

 

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 532 44 II. Slope Operation Safe Operation Practices for Ride=On MowersGeneral Operation Defects or other reproductive harm. Wash handsSafe Operation Practices ServiceRules IV. TowingContents Unassembled Parts Steering WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Deck Levelness To Adjust Seat See FigCheck Tire Pressure Check for Proper Position of BeltsOperation System ROSKnow Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Move Forward and Backward To Adjust Mower Cutting HeightTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigTo Operate on Hills To Stop Mower BladesReverse Operation System ROS To Transport See FigsCheck Engine OiL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolineMowing Tips Purge TransmissionSchedule MaintenanceGeneral Recommendations Before Each USEBlade Care BatteryTractor Blade Removal See FigTransaxle Cooling Clean AIR Screen=BELTS Transaxle Pump FluidIN=LINE Fuel Filter See Fig CleaningMuffler Deck Washout Port See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs Tachment Lift Lever SeeAdjustments = Turn Steering Wheel Left and Position Mower See FigANTI=SWAY Attach Mower Side Suspension Arms a to Chassis See Fig Attach Rear Lift Links C See FigTo Level Mower Your hands with gloves and/or wrapTo Replace Mower Blade Drive Belt To Replace Motion Drive BeltTo Remove Wheel See Fig To Adjust Steering Wheel AlignmentTo Check Brake Front Wheel TOE-IN/CAMBEREngine TransmissionSee Fig Fuel System TractorOther Engine OiLTroubleshooting Working If so Battery Will notPoor cut = uneven ChargeSchematic Tractor - Model Number YTH2348Electrical KEY Part NO. NO.DESCRIPTIONTractor - Model Number YTH2348 Chassis Chassis Tractor - Model Number KEYTractor - Model Number YTH2348 Drive Drive Idler FlatEngine Tractor - Model Number YTH2348 Engine DESCRiPTiONSteering Assembly I68Seat Assembly DescriptionTractor - Model Number YTH2348 Mower Deck Mower Deck KEY Part DescriptionMower Lift NO. NO.DESCRiPTiON Tractor - Model Number YTH2348 DecalsWheels and Tires NO. NO.DESCRIPTIONModel K46BT Tufftorq Transaxle Model Number K46BTTufftorq Transaxle Model Number K46BT 10t Tractor - Model Number YTH2348 LO5@I33 Kit Magneto Side 133 699724 Pump 524 691032 Seal-Dipstick Tube 1022 690971 Consumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Warranty Chart 11111111111111111111All other Pressure Washers 6027PW, 9032PW, 1340PW Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down HILL, not Across Hill Degrees MAXHusqvarna
Top Page Image Contents