Husqvarna iZ4817SKAA/968999356 manual Fuel Shut Off Valve, Seat Adjustment Lever, Choke Control

Page 23

CONTROLS

10. Fuel Shut Off Valve

The fuel shut off valve is located at the right rear of the seat. The valve has three positions; right tank, left tank and center is the off position.

11. Seat Adjustment Lever

The seat can be adjusted lengthways. When making adjustments, the lever under the front edge of the seat is moved to the left (as seen by the driver in the seat), after which the seat can be moved backward or forward.

12. Choke Control

The choke control is used for cold starts in order to provide the engine with a richer fuel mixture.

For cold starts the control should be pulled out.

8011-506

Fuel valve

8011-441

Lengthways adjustment

8011-508

Choke control

English-21

Image 23

Contents English Operator´s manualPage OPERATOR’S MANUAL RIDER iZ SERIES ContentsEnglish-2 General INTRODUCTIONIntroduction CongratulationsManufacturing Number Good Servicexxxx xxxxxx SYMBOLS AND DECALSSymbols and Decals Xxxxxxx xxxx xxxxxxxx xxx Xxxxx xxxxxx xx xxxxxxxx xxxxx xxxRead General Operation SAFETY INSTRUCTIONSSafety Instructions Operate machine only in daylight or good artificial light Slope Operation Personal Safety EquipmentChildren Risk for burns if touched MaintenanceSafe Handling of Gasoline The engine and the exhaust system, become very hot during operationAlways use protective glasses when handling the battery General MaintenanceEnglish-13 Risk of sparkingIMPORTANT INFORMATION TransportCustomer responsibilities Roll over Protecion system ROPSControl Locations CONTROLSControls 1 Forward 2 Neutral 3 Neutral slot, Neutral lock 4 Reverse 1. Motion Control Levers4. Parking Brake 2. Hour Meter3. Tracking Knob 7. Fuses 5. Blade switch6. Ignition Switch allow engine and exhaust system to cool at least two 2 minutes see the safety rules8. Seat Locking Device 9. Refueling12. Choke Control 11. Seat Adjustment Lever10. Fuel Shut Off Valve The mower deck’s lifting lever 13. Throttle Control14. Lifting Lever for the Mower Deck Throttle controlOnly rotate valve 1/4 - 1/2 turn to release system AccessoriesPump release valves Cutting height pedalTo move forward and backward OPERATIONOperation TrainingStarting the Engine Roll bar and safety beltThe seat belt must be used when the roll bar is in upright position Before StartingEnglish-26 Depress the control for disengaging the mower deckSteering controls in the outward, locked neutral position Set the throttleEnglish-27 Set the choke controlOpen the fuel valve Turn to the start positionIMPORTANT INFORMATION Do not run the starter for more than USE FULL THROTTLE WHEN MOWINGTo remove cables, reverse order To start an engine with a weak batteryTo attach jumper cables Running The mower deck’s anti-scalp rollers shall be evenly adjustedEnsure that no one is near the machine when engaging the blade switch English-31 Operating on hillsMowing Tips Stopping the Engine the parking brake is on No adjustments or maintenance to carried out unlessMoving by Hand the engine is stopped the ignition key has been removedMaintenance Schedule MAINTENANCEMaintenance English-36 Always use two wrenches for the terminal screws BatteryTo clean battery and terminals Replacing batteryFitting the wrong spark plug type can damage the engine Ignition SystemChecking the Safety System 8011-553 Safety systemIgnition system English-40Checking the Engines Cooling Air Intake Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable Do not wash the paper filter. Do not oil the paper filter Do not used compressed air to clean the air filterReplacing the Air Filter Standard air filterDo not wash the paper filter. Do not oil the paper filter Dust cap Cyclon air filter maintenance1. Remove the end cover Filter replacementAir filter indicator optional Checking the Fuel Pump’s Air Filter Replacing the Fuel FilterChecking the V-belts Faulty adjustment can cause an accidentChecking Tire Pressures Checking the Parking BrakePump belt Checking the BladesRemove blade bolt by turning counterclockwise Blade replacementDo not use lower grade hardware than specified 3. Turn ignition switch to “OFF” position and remove the key Adjusting the Mower DeckBefore performing any service or adjustment checklist 2. Place the blade-switch in the disengaged positionEngine oil cooler Adjust Anti-scalp rollers with the mower on a flat level surfaceTo adjust anti-scalp rollers Caster Wheels Cleaning and WashingUse protective glasses when cleaning and washing Removal and installation of caster wheelLubrication Schedule LUBRICATIONLubrication 1. Hydraulic System, Oil Level Lubricating the CablesShaft Bushings and Linkage Lubricating in Accordance with the Lubrication ScheduleAvoid skin contact wash with soap and water in case of spills 3. Engine Oil Kohler Engine Changing the Engine OilCheck oil before each use as follows Checking the Oil LevelOil Type Oil Recommendations3. Engine Oil Kawasaki Engine Changing the Engine Oil 5. Front Wheel Mount 4. Throttle and Choke Cables, Lever BearingsLubricating the cutting height adjuster 8. Mower Deck Height Adjuster6. Front Wheel Bearings 7. Deck belt pulleys11. Mower Deck Struts 9. Belt Adjuster, Mower Deck10. Steering Control Shafts Tip the driver’s seat 12. Brake Arms 13. Belt Adjuster, Hydraulic Pumps14. Changing the Oil Filter Cause TROUBLE SHOOTING GUIDETrouble Shooting Guide ProblemEnglish-64 Winter Storage ServiceSTORAGE StorageWiring diagrams WIRING DIAGRAMSiZ5221TKAA TECHNICAL DATATechnical Data iZ4819TSKAAEnglish-68 Overall dimensionsEquipment ProductivityEnglish-69 iZ5225TXPKOAiZ5224TLKOA iZ6125TKOAEnglish-70 Dual levers, foam gripped iZ4217TSKAAiZ4817TSKAA iZ4821TKAAEnglish-72 English-73 iZ5223TKOAEnglish-74 English-75 Torque SpecificationsUSA requirements CONFORMITY CERTIFICATESConformity Certificates Action SERVICE JOURNALService Journal Delivery ServiceAfter the First 8 Hours English-79 25-Hour ServiceEnglish-80 50-Hour Service100-Hour Service 300-Hour Service At Least Once Each Year 112673R0112/05/05