Husqvarna iZ4217TSKAA/9689999254, iZ4817SKAA/968999356 manual Changing the Oil Filter, Lubrication

Page 64

LUBRICATION

14. Changing the Oil Filter

1.Drain the engine oil in accordance with the work description under the heading Engine Oil/Change Engine Oil.

2.Remove the oil filter. If necessary, use a filter remover.

3.Wipe new, clean engine oil onto the seal for the new filter.

4.Mount the filter by hand with + 3/4 turn.

5.Run the engine warm, then check that there are no leaks around the oil filter seal.

6.Check the oil level in the engine, fill to proper level if necessary. The oil filter holds 0.2 qt (0.2 liters) of oil.

8011-570

Changing the oil filter Kawasaki

8011-745

Changing the oil filter Kohler

English-62

Image 64

Contents Operator´s manual EnglishPage Contents OPERATOR’S MANUAL RIDER iZ SERIESEnglish-2 INTRODUCTION IntroductionCongratulations GeneralGood Service Manufacturing NumberSYMBOLS AND DECALS Symbols and DecalsXxxxxxx xxxx xxxxxxxx xxx Xxxxx xxxxxx xx xxxxxxxx xxxxx xxx xxxx xxxxxxRead Safety Instructions SAFETY INSTRUCTIONSGeneral Operation Operate machine only in daylight or good artificial light Personal Safety Equipment Slope OperationChildren Maintenance Safe Handling of GasolineThe engine and the exhaust system, become very hot during operation Risk for burns if touchedGeneral Maintenance Always use protective glasses when handling the batteryRisk of sparking English-13Transport IMPORTANT INFORMATIONRoll over Protecion system ROPS Customer responsibilitiesControls CONTROLSControl Locations 1. Motion Control Levers 1 Forward 2 Neutral 3 Neutral slot, Neutral lock 4 Reverse3. Tracking Knob 2. Hour Meter4. Parking Brake 6. Ignition Switch 5. Blade switch7. Fuses see the safety rules 8. Seat Locking Device9. Refueling allow engine and exhaust system to cool at least two 2 minutes10. Fuel Shut Off Valve 11. Seat Adjustment Lever12. Choke Control 13. Throttle Control 14. Lifting Lever for the Mower DeckThrottle control The mower deck’s lifting leverAccessories Pump release valvesCutting height pedal Only rotate valve 1/4 - 1/2 turn to release systemOPERATION OperationTraining To move forward and backwardRoll bar and safety belt The seat belt must be used when the roll bar is in upright positionBefore Starting Starting the EngineDepress the control for disengaging the mower deck Steering controls in the outward, locked neutral positionSet the throttle English-26Set the choke control Open the fuel valveTurn to the start position English-27USE FULL THROTTLE WHEN MOWING IMPORTANT INFORMATION Do not run the starter for more thanTo attach jumper cables To start an engine with a weak batteryTo remove cables, reverse order Ensure that no one is near the machine when engaging the blade switch The mower deck’s anti-scalp rollers shall be evenly adjustedRunning Operating on hills English-31Mowing Tips Stopping the Engine No adjustments or maintenance to carried out unless Moving by Handthe engine is stopped the ignition key has been removed the parking brake is onMaintenance MAINTENANCEMaintenance Schedule English-36 Battery To clean battery and terminalsReplacing battery Always use two wrenches for the terminal screwsIgnition System Fitting the wrong spark plug type can damage the engineChecking the Safety System Safety system Ignition systemEnglish-40 8011-553Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake Do not used compressed air to clean the air filter Replacing the Air FilterStandard air filter Do not wash the paper filter. Do not oil the paper filterCyclon air filter maintenance Do not wash the paper filter. Do not oil the paper filter Dust capAir filter indicator optional Filter replacement1. Remove the end cover Replacing the Fuel Filter Checking the Fuel Pump’s Air FilterFaulty adjustment can cause an accident Checking Tire PressuresChecking the Parking Brake Checking the V-beltsChecking the Blades Pump beltDo not use lower grade hardware than specified Blade replacementRemove blade bolt by turning counterclockwise Adjusting the Mower Deck Before performing any service or adjustment checklist2. Place the blade-switch in the disengaged position 3. Turn ignition switch to “OFF” position and remove the keyTo adjust anti-scalp rollers Adjust Anti-scalp rollers with the mower on a flat level surfaceEngine oil cooler Cleaning and Washing Use protective glasses when cleaning and washingRemoval and installation of caster wheel Caster WheelsLubrication LUBRICATIONLubrication Schedule Lubricating the Cables Shaft Bushings and LinkageLubricating in Accordance with the Lubrication Schedule 1. Hydraulic System, Oil Level3. Engine Oil Kohler Engine Changing the Engine Oil Avoid skin contact wash with soap and water in case of spillsChecking the Oil Level Check oil before each use as followsOil Recommendations Oil Type3. Engine Oil Kawasaki Engine Changing the Engine Oil 4. Throttle and Choke Cables, Lever Bearings 5. Front Wheel Mount8. Mower Deck Height Adjuster 6. Front Wheel Bearings7. Deck belt pulleys Lubricating the cutting height adjuster10. Steering Control Shafts Tip the driver’s seat 9. Belt Adjuster, Mower Deck11. Mower Deck Struts 13. Belt Adjuster, Hydraulic Pumps 12. Brake Arms14. Changing the Oil Filter TROUBLE SHOOTING GUIDE Trouble Shooting GuideProblem CauseEnglish-64 Service STORAGEStorage Winter StorageWIRING DIAGRAMS Wiring diagramsTECHNICAL DATA Technical DataiZ4819TSKAA iZ5221TKAAOverall dimensions EquipmentProductivity English-68iZ5225TXPKOA iZ5224TLKOAiZ6125TKOA English-69English-70 iZ4217TSKAA iZ4817TSKAAiZ4821TKAA Dual levers, foam grippedEnglish-72 iZ5223TKOA English-73English-74 Torque Specifications English-75Conformity Certificates CONFORMITY CERTIFICATESUSA requirements SERVICE JOURNAL Service JournalDelivery Service ActionAfter the First 8 Hours 25-Hour Service English-7950-Hour Service English-80100-Hour Service 300-Hour Service At Least Once Each Year 112673R0112/05/05