Husqvarna iZ4217TSKAA/9689999254 Seat Locking Device, Refueling, see the safety rules, Controls

Page 22
8. Seat Locking Device

CONTROLS

8. Seat Locking Device

Under the rear part of the seat is a locking device that locks the seat into its folded position. The seat has hinges at the front edge and can be folded forward when the locking device is pushed.

9. Refueling

The machine has two fuel tanks, one on each side just behind the seat. The tanks take 5.7 gallons (22 liters) each.

The engine will run on a minimum of 87-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used beneficially. See also Technical Data concerning methanol and ethanol fuels.

WARNING!

Gasoline is highly flammable. Observe caution and fill the tank outdoors

(see the safety rules).

WARNING!

The engine and the exhaust system, become very hot during operation.

Risk for burns if touched.

allow engine and exhaust system to cool at least two (2) minutes.

WARNING!

Fill to bottom of filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

When operating in temperatures below 32 °F. (0 °C.), use fresh, clean winter grade gasoline to help insure good cold weather starting.

8011-440

The seat’s locking device

8011-524

Fuel tanks

IMPORTANT INFORMATION

Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage Instructions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur.

English-20

Image 22
Contents Operator´s manual EnglishPage Contents OPERATOR’S MANUAL RIDER iZ SERIESEnglish-2 Congratulations INTRODUCTIONIntroduction GeneralGood Service Manufacturing NumberXxxxxxx xxxx xxxxxxxx xxx Xxxxx xxxxxx xx xxxxxxxx xxxxx xxx SYMBOLS AND DECALSSymbols and Decals xxxx xxxxxxRead Safety Instructions SAFETY INSTRUCTIONSGeneral Operation Operate machine only in daylight or good artificial light Personal Safety Equipment Slope OperationChildren The engine and the exhaust system, become very hot during operation MaintenanceSafe Handling of Gasoline Risk for burns if touchedGeneral Maintenance Always use protective glasses when handling the batteryRisk of sparking English-13Transport IMPORTANT INFORMATIONRoll over Protecion system ROPS Customer responsibilitiesControls CONTROLSControl Locations 1. Motion Control Levers 1 Forward 2 Neutral 3 Neutral slot, Neutral lock 4 Reverse3. Tracking Knob 2. Hour Meter4. Parking Brake 6. Ignition Switch 5. Blade switch7. Fuses 9. Refueling see the safety rules8. Seat Locking Device allow engine and exhaust system to cool at least two 2 minutes10. Fuel Shut Off Valve 11. Seat Adjustment Lever12. Choke Control Throttle control 13. Throttle Control14. Lifting Lever for the Mower Deck The mower deck’s lifting leverCutting height pedal AccessoriesPump release valves Only rotate valve 1/4 - 1/2 turn to release systemTraining OPERATIONOperation To move forward and backwardBefore Starting Roll bar and safety beltThe seat belt must be used when the roll bar is in upright position Starting the EngineSet the throttle Depress the control for disengaging the mower deckSteering controls in the outward, locked neutral position English-26Turn to the start position Set the choke controlOpen the fuel valve English-27USE FULL THROTTLE WHEN MOWING IMPORTANT INFORMATION Do not run the starter for more thanTo attach jumper cables To start an engine with a weak batteryTo remove cables, reverse order Ensure that no one is near the machine when engaging the blade switch The mower deck’s anti-scalp rollers shall be evenly adjustedRunning Operating on hills English-31Mowing Tips Stopping the Engine the engine is stopped the ignition key has been removed No adjustments or maintenance to carried out unlessMoving by Hand the parking brake is onMaintenance MAINTENANCEMaintenance Schedule English-36 Replacing battery BatteryTo clean battery and terminals Always use two wrenches for the terminal screwsIgnition System Fitting the wrong spark plug type can damage the engineChecking the Safety System English-40 Safety systemIgnition system 8011-553Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake Standard air filter Do not used compressed air to clean the air filterReplacing the Air Filter Do not wash the paper filter. Do not oil the paper filterCyclon air filter maintenance Do not wash the paper filter. Do not oil the paper filter Dust capAir filter indicator optional Filter replacement1. Remove the end cover Replacing the Fuel Filter Checking the Fuel Pump’s Air FilterChecking the Parking Brake Faulty adjustment can cause an accidentChecking Tire Pressures Checking the V-beltsChecking the Blades Pump beltDo not use lower grade hardware than specified Blade replacementRemove blade bolt by turning counterclockwise 2. Place the blade-switch in the disengaged position Adjusting the Mower DeckBefore performing any service or adjustment checklist 3. Turn ignition switch to “OFF” position and remove the keyTo adjust anti-scalp rollers Adjust Anti-scalp rollers with the mower on a flat level surfaceEngine oil cooler Removal and installation of caster wheel Cleaning and WashingUse protective glasses when cleaning and washing Caster WheelsLubrication LUBRICATIONLubrication Schedule Lubricating in Accordance with the Lubrication Schedule Lubricating the CablesShaft Bushings and Linkage 1. Hydraulic System, Oil Level3. Engine Oil Kohler Engine Changing the Engine Oil Avoid skin contact wash with soap and water in case of spillsChecking the Oil Level Check oil before each use as followsOil Recommendations Oil Type3. Engine Oil Kawasaki Engine Changing the Engine Oil 4. Throttle and Choke Cables, Lever Bearings 5. Front Wheel Mount7. Deck belt pulleys 8. Mower Deck Height Adjuster6. Front Wheel Bearings Lubricating the cutting height adjuster10. Steering Control Shafts Tip the driver’s seat 9. Belt Adjuster, Mower Deck11. Mower Deck Struts 13. Belt Adjuster, Hydraulic Pumps 12. Brake Arms14. Changing the Oil Filter Problem TROUBLE SHOOTING GUIDETrouble Shooting Guide CauseEnglish-64 Storage ServiceSTORAGE Winter StorageWIRING DIAGRAMS Wiring diagramsiZ4819TSKAA TECHNICAL DATATechnical Data iZ5221TKAAProductivity Overall dimensionsEquipment English-68iZ6125TKOA iZ5225TXPKOAiZ5224TLKOA English-69English-70 iZ4821TKAA iZ4217TSKAAiZ4817TSKAA Dual levers, foam grippedEnglish-72 iZ5223TKOA English-73English-74 Torque Specifications English-75Conformity Certificates CONFORMITY CERTIFICATESUSA requirements Delivery Service SERVICE JOURNALService Journal ActionAfter the First 8 Hours 25-Hour Service English-7950-Hour Service English-80100-Hour Service 300-Hour Service At Least Once Each Year 112673R0112/05/05