Husqvarna iZ4817SKAA/968999356 Operation, Set the choke control, Open the fuel valve, English-27

Page 29

OPERATION

7.If the engine is cold, the choke control shall be pulled out to its extents.

8.Open the fuel valve for the selected fuel tank.

8011-508

Set the choke control

8011-506

Open the fuel valve

9.Press in and turn the ignition key to the start position.

8011-742

Turn to the start position

English-27

Image 29

Contents English Operator´s manualPage OPERATOR’S MANUAL RIDER iZ SERIES ContentsEnglish-2 Introduction INTRODUCTIONCongratulations GeneralManufacturing Number Good ServiceSymbols and Decals SYMBOLS AND DECALSXxxxxxx xxxx xxxxxxxx xxx Xxxxx xxxxxx xx xxxxxxxx xxxxx xxx xxxx xxxxxxRead General Operation SAFETY INSTRUCTIONSSafety Instructions Operate machine only in daylight or good artificial light Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline MaintenanceThe engine and the exhaust system, become very hot during operation Risk for burns if touchedAlways use protective glasses when handling the battery General MaintenanceEnglish-13 Risk of sparkingIMPORTANT INFORMATION TransportCustomer responsibilities Roll over Protecion system ROPSControl Locations CONTROLSControls 1 Forward 2 Neutral 3 Neutral slot, Neutral lock 4 Reverse 1. Motion Control Levers4. Parking Brake 2. Hour Meter3. Tracking Knob 7. Fuses 5. Blade switch6. Ignition Switch 8. Seat Locking Device see the safety rules9. Refueling allow engine and exhaust system to cool at least two 2 minutes12. Choke Control 11. Seat Adjustment Lever10. Fuel Shut Off Valve 14. Lifting Lever for the Mower Deck 13. Throttle ControlThrottle control The mower deck’s lifting leverPump release valves AccessoriesCutting height pedal Only rotate valve 1/4 - 1/2 turn to release systemOperation OPERATIONTraining To move forward and backwardThe seat belt must be used when the roll bar is in upright position Roll bar and safety beltBefore Starting Starting the EngineSteering controls in the outward, locked neutral position Depress the control for disengaging the mower deckSet the throttle English-26Open the fuel valve Set the choke controlTurn to the start position English-27IMPORTANT INFORMATION Do not run the starter for more than USE FULL THROTTLE WHEN MOWINGTo remove cables, reverse order To start an engine with a weak batteryTo attach jumper cables Running The mower deck’s anti-scalp rollers shall be evenly adjustedEnsure that no one is near the machine when engaging the blade switch English-31 Operating on hillsMowing Tips Stopping the Engine Moving by Hand No adjustments or maintenance to carried out unlessthe engine is stopped the ignition key has been removed the parking brake is onMaintenance Schedule MAINTENANCEMaintenance English-36 To clean battery and terminals BatteryReplacing battery Always use two wrenches for the terminal screwsFitting the wrong spark plug type can damage the engine Ignition SystemChecking the Safety System Ignition system Safety systemEnglish-40 8011-553Checking the Engines Cooling Air Intake Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable Replacing the Air Filter Do not used compressed air to clean the air filterStandard air filter Do not wash the paper filter. Do not oil the paper filterDo not wash the paper filter. Do not oil the paper filter Dust cap Cyclon air filter maintenance1. Remove the end cover Filter replacementAir filter indicator optional Checking the Fuel Pump’s Air Filter Replacing the Fuel FilterChecking Tire Pressures Faulty adjustment can cause an accidentChecking the Parking Brake Checking the V-beltsPump belt Checking the BladesRemove blade bolt by turning counterclockwise Blade replacementDo not use lower grade hardware than specified Before performing any service or adjustment checklist Adjusting the Mower Deck2. Place the blade-switch in the disengaged position 3. Turn ignition switch to “OFF” position and remove the keyEngine oil cooler Adjust Anti-scalp rollers with the mower on a flat level surfaceTo adjust anti-scalp rollers Use protective glasses when cleaning and washing Cleaning and WashingRemoval and installation of caster wheel Caster WheelsLubrication Schedule LUBRICATIONLubrication Shaft Bushings and Linkage Lubricating the CablesLubricating in Accordance with the Lubrication Schedule 1. Hydraulic System, Oil LevelAvoid skin contact wash with soap and water in case of spills 3. Engine Oil Kohler Engine Changing the Engine OilCheck oil before each use as follows Checking the Oil LevelOil Type Oil Recommendations3. Engine Oil Kawasaki Engine Changing the Engine Oil 5. Front Wheel Mount 4. Throttle and Choke Cables, Lever Bearings6. Front Wheel Bearings 8. Mower Deck Height Adjuster7. Deck belt pulleys Lubricating the cutting height adjuster11. Mower Deck Struts 9. Belt Adjuster, Mower Deck10. Steering Control Shafts Tip the driver’s seat 12. Brake Arms 13. Belt Adjuster, Hydraulic Pumps14. Changing the Oil Filter Trouble Shooting Guide TROUBLE SHOOTING GUIDEProblem CauseEnglish-64 STORAGE ServiceStorage Winter StorageWiring diagrams WIRING DIAGRAMSTechnical Data TECHNICAL DATAiZ4819TSKAA iZ5221TKAAEquipment Overall dimensionsProductivity English-68iZ5224TLKOA iZ5225TXPKOAiZ6125TKOA English-69English-70 iZ4817TSKAA iZ4217TSKAAiZ4821TKAA Dual levers, foam grippedEnglish-72 English-73 iZ5223TKOAEnglish-74 English-75 Torque SpecificationsUSA requirements CONFORMITY CERTIFICATESConformity Certificates Service Journal SERVICE JOURNALDelivery Service ActionAfter the First 8 Hours English-79 25-Hour ServiceEnglish-80 50-Hour Service100-Hour Service 300-Hour Service At Least Once Each Year 112673R0112/05/05