Husqvarna iZ4817SKAA/968999356 To start an engine with a weak battery, To attach jumper cables

Page 31

To start an engine with a weak battery

OPERATION

To start an engine with a weak battery

WARNING!

Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "Battery" in the the "Maintenance" section).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT INFORMATION

Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower battery to start other vehicles.

To attach jumper cables

• Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery.

8011-642

• Connect the other end of the BLACK	Jumper cables connection
cable to a good CHASSIS GROUND on
the mower with the discharged battery,
away from the fuel tank and battery.

To remove cables, reverse order

•Remove BLACK cable first from chassis and then from the fully charged battery.

•Remove RED cable last from both batteries.

English-29

Image 31

Contents English Operator´s manualPage OPERATOR’S MANUAL RIDER iZ SERIES ContentsEnglish-2 General INTRODUCTIONIntroduction CongratulationsManufacturing Number Good Servicexxxx xxxxxx SYMBOLS AND DECALSSymbols and Decals Xxxxxxx xxxx xxxxxxxx xxx Xxxxx xxxxxx xx xxxxxxxx xxxxx xxxRead Safety Instructions SAFETY INSTRUCTIONSGeneral Operation Operate machine only in daylight or good artificial light Slope Operation Personal Safety EquipmentChildren Risk for burns if touched MaintenanceSafe Handling of Gasoline The engine and the exhaust system, become very hot during operationAlways use protective glasses when handling the battery General MaintenanceEnglish-13 Risk of sparkingIMPORTANT INFORMATION TransportCustomer responsibilities Roll over Protecion system ROPSControls CONTROLSControl Locations 1 Forward 2 Neutral 3 Neutral slot, Neutral lock 4 Reverse 1. Motion Control Levers3. Tracking Knob 2. Hour Meter4. Parking Brake 6. Ignition Switch 5. Blade switch7. Fuses allow engine and exhaust system to cool at least two 2 minutes see the safety rules8. Seat Locking Device 9. Refueling10. Fuel Shut Off Valve 11. Seat Adjustment Lever12. Choke Control The mower deck’s lifting lever 13. Throttle Control14. Lifting Lever for the Mower Deck Throttle controlOnly rotate valve 1/4 - 1/2 turn to release system AccessoriesPump release valves Cutting height pedalTo move forward and backward OPERATIONOperation TrainingStarting the Engine Roll bar and safety beltThe seat belt must be used when the roll bar is in upright position Before StartingEnglish-26 Depress the control for disengaging the mower deckSteering controls in the outward, locked neutral position Set the throttleEnglish-27 Set the choke controlOpen the fuel valve Turn to the start positionIMPORTANT INFORMATION Do not run the starter for more than USE FULL THROTTLE WHEN MOWINGTo attach jumper cables To start an engine with a weak batteryTo remove cables, reverse order Ensure that no one is near the machine when engaging the blade switch The mower deck’s anti-scalp rollers shall be evenly adjustedRunning English-31 Operating on hillsMowing Tips Stopping the Engine the parking brake is on No adjustments or maintenance to carried out unlessMoving by Hand the engine is stopped the ignition key has been removedMaintenance MAINTENANCEMaintenance Schedule English-36 Always use two wrenches for the terminal screws BatteryTo clean battery and terminals Replacing batteryFitting the wrong spark plug type can damage the engine Ignition SystemChecking the Safety System 8011-553 Safety systemIgnition system English-40Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake Do not wash the paper filter. Do not oil the paper filter Do not used compressed air to clean the air filterReplacing the Air Filter Standard air filterDo not wash the paper filter. Do not oil the paper filter Dust cap Cyclon air filter maintenanceAir filter indicator optional Filter replacement1. Remove the end cover Checking the Fuel Pump’s Air Filter Replacing the Fuel FilterChecking the V-belts Faulty adjustment can cause an accidentChecking Tire Pressures Checking the Parking BrakePump belt Checking the BladesDo not use lower grade hardware than specified Blade replacementRemove blade bolt by turning counterclockwise 3. Turn ignition switch to “OFF” position and remove the key Adjusting the Mower DeckBefore performing any service or adjustment checklist 2. Place the blade-switch in the disengaged positionTo adjust anti-scalp rollers Adjust Anti-scalp rollers with the mower on a flat level surfaceEngine oil cooler Caster Wheels Cleaning and WashingUse protective glasses when cleaning and washing Removal and installation of caster wheelLubrication LUBRICATIONLubrication Schedule 1. Hydraulic System, Oil Level Lubricating the CablesShaft Bushings and Linkage Lubricating in Accordance with the Lubrication ScheduleAvoid skin contact wash with soap and water in case of spills 3. Engine Oil Kohler Engine Changing the Engine OilCheck oil before each use as follows Checking the Oil LevelOil Type Oil Recommendations3. Engine Oil Kawasaki Engine Changing the Engine Oil 5. Front Wheel Mount 4. Throttle and Choke Cables, Lever BearingsLubricating the cutting height adjuster 8. Mower Deck Height Adjuster6. Front Wheel Bearings 7. Deck belt pulleys10. Steering Control Shafts Tip the driver’s seat 9. Belt Adjuster, Mower Deck11. Mower Deck Struts 12. Brake Arms 13. Belt Adjuster, Hydraulic Pumps14. Changing the Oil Filter Cause TROUBLE SHOOTING GUIDETrouble Shooting Guide ProblemEnglish-64 Winter Storage ServiceSTORAGE StorageWiring diagrams WIRING DIAGRAMSiZ5221TKAA TECHNICAL DATATechnical Data iZ4819TSKAAEnglish-68 Overall dimensionsEquipment ProductivityEnglish-69 iZ5225TXPKOAiZ5224TLKOA iZ6125TKOAEnglish-70 Dual levers, foam gripped iZ4217TSKAAiZ4817TSKAA iZ4821TKAAEnglish-72 English-73 iZ5223TKOAEnglish-74 English-75 Torque SpecificationsConformity Certificates CONFORMITY CERTIFICATESUSA requirements Action SERVICE JOURNALService Journal Delivery ServiceAfter the First 8 Hours English-79 25-Hour ServiceEnglish-80 50-Hour Service100-Hour Service 300-Hour Service At Least Once Each Year 112673R0112/05/05