Husqvarna iZ4817SKAA/968999356 Cyclon air filter maintenance, Maintenance, Important Information

Page 45

Cyclon air filter maintenance

MAINTENANCE

Cyclon air filter maintenance

If the engine seems weak or runs unevenly, the air filter may be clogged. If running with a soiled air filter, the spark plugs can obtain a coating that disrupts operation.

For this reason, it is important to replace the air filter regularly (see the heading Maintenance Schedule for the proper service interval).

WARNING!

The engine and the exhaust system, become very hot during operation. Risk for burns if touched. Allow engine and exhust ststem to cool at least two (2) minuts.

Cleaning/replacing the air filter is carried out as follows:

IMPORTANT INFORMATION

Do not used compressed air to clean the air filter.

Do not wash the paper filter. Do not oil the paper filter.

Dust cap

Check the dust cap every day by pressing the rubber valve with two fingers to let out the dirt.

IMPORTANT INFORMATION

The end cover must be installed with the rubber valve pointing downwards, otherwise the rubber valve will not function.

Clean the dust cap by removing the end cover of the the air cleaner and clean the inside.

8011-447

Pressing the rubber valve

8011-448

Removing the end cover

English-43

Image 45

Contents English Operator´s manualPage OPERATOR’S MANUAL RIDER iZ SERIES ContentsEnglish-2 Introduction INTRODUCTIONCongratulations GeneralManufacturing Number Good ServiceSymbols and Decals SYMBOLS AND DECALSXxxxxxx xxxx xxxxxxxx xxx Xxxxx xxxxxx xx xxxxxxxx xxxxx xxx xxxx xxxxxxRead SAFETY INSTRUCTIONS Safety InstructionsGeneral Operation Operate machine only in daylight or good artificial light Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline MaintenanceThe engine and the exhaust system, become very hot during operation Risk for burns if touchedAlways use protective glasses when handling the battery General MaintenanceEnglish-13 Risk of sparkingIMPORTANT INFORMATION TransportCustomer responsibilities Roll over Protecion system ROPSCONTROLS ControlsControl Locations 1 Forward 2 Neutral 3 Neutral slot, Neutral lock 4 Reverse 1. Motion Control Levers2. Hour Meter 3. Tracking Knob4. Parking Brake 5. Blade switch 6. Ignition Switch7. Fuses 8. Seat Locking Device see the safety rules9. Refueling allow engine and exhaust system to cool at least two 2 minutes11. Seat Adjustment Lever 10. Fuel Shut Off Valve12. Choke Control 14. Lifting Lever for the Mower Deck 13. Throttle ControlThrottle control The mower deck’s lifting leverPump release valves AccessoriesCutting height pedal Only rotate valve 1/4 - 1/2 turn to release systemOperation OPERATIONTraining To move forward and backwardThe seat belt must be used when the roll bar is in upright position Roll bar and safety beltBefore Starting Starting the EngineSteering controls in the outward, locked neutral position Depress the control for disengaging the mower deckSet the throttle English-26Open the fuel valve Set the choke controlTurn to the start position English-27IMPORTANT INFORMATION Do not run the starter for more than USE FULL THROTTLE WHEN MOWINGTo start an engine with a weak battery To attach jumper cablesTo remove cables, reverse order The mower deck’s anti-scalp rollers shall be evenly adjusted Ensure that no one is near the machine when engaging the blade switchRunning English-31 Operating on hillsMowing Tips Stopping the Engine Moving by Hand No adjustments or maintenance to carried out unlessthe engine is stopped the ignition key has been removed the parking brake is onMAINTENANCE MaintenanceMaintenance Schedule English-36 To clean battery and terminals BatteryReplacing battery Always use two wrenches for the terminal screwsFitting the wrong spark plug type can damage the engine Ignition SystemChecking the Safety System Ignition system Safety systemEnglish-40 8011-553Checking and Adjusting the Throttle Cable Checking and Adjusting the Choke CableChecking the Engines Cooling Air Intake Replacing the Air Filter Do not used compressed air to clean the air filterStandard air filter Do not wash the paper filter. Do not oil the paper filterDo not wash the paper filter. Do not oil the paper filter Dust cap Cyclon air filter maintenanceFilter replacement Air filter indicator optional1. Remove the end cover Checking the Fuel Pump’s Air Filter Replacing the Fuel FilterChecking Tire Pressures Faulty adjustment can cause an accidentChecking the Parking Brake Checking the V-beltsPump belt Checking the BladesBlade replacement Do not use lower grade hardware than specifiedRemove blade bolt by turning counterclockwise Before performing any service or adjustment checklist Adjusting the Mower Deck2. Place the blade-switch in the disengaged position 3. Turn ignition switch to “OFF” position and remove the keyAdjust Anti-scalp rollers with the mower on a flat level surface To adjust anti-scalp rollersEngine oil cooler Use protective glasses when cleaning and washing Cleaning and WashingRemoval and installation of caster wheel Caster WheelsLUBRICATION LubricationLubrication Schedule Shaft Bushings and Linkage Lubricating the CablesLubricating in Accordance with the Lubrication Schedule 1. Hydraulic System, Oil LevelAvoid skin contact wash with soap and water in case of spills 3. Engine Oil Kohler Engine Changing the Engine OilCheck oil before each use as follows Checking the Oil LevelOil Type Oil Recommendations3. Engine Oil Kawasaki Engine Changing the Engine Oil 5. Front Wheel Mount 4. Throttle and Choke Cables, Lever Bearings6. Front Wheel Bearings 8. Mower Deck Height Adjuster7. Deck belt pulleys Lubricating the cutting height adjuster9. Belt Adjuster, Mower Deck 10. Steering Control Shafts Tip the driver’s seat11. Mower Deck Struts 12. Brake Arms 13. Belt Adjuster, Hydraulic Pumps14. Changing the Oil Filter Trouble Shooting Guide TROUBLE SHOOTING GUIDEProblem CauseEnglish-64 STORAGE ServiceStorage Winter StorageWiring diagrams WIRING DIAGRAMSTechnical Data TECHNICAL DATAiZ4819TSKAA iZ5221TKAAEquipment Overall dimensionsProductivity English-68iZ5224TLKOA iZ5225TXPKOAiZ6125TKOA English-69English-70 iZ4817TSKAA iZ4217TSKAAiZ4821TKAA Dual levers, foam grippedEnglish-72 English-73 iZ5223TKOAEnglish-74 English-75 Torque SpecificationsCONFORMITY CERTIFICATES Conformity CertificatesUSA requirements Service Journal SERVICE JOURNALDelivery Service ActionAfter the First 8 Hours English-79 25-Hour ServiceEnglish-80 50-Hour Service100-Hour Service 300-Hour Service At Least Once Each Year 112673R0112/05/05