Husqvarna CTH210xp, CTH150 XP To Assemble Bagger, Bagger adjustment, Horizontal adjustment

Page 25

1

 

 

 

2

 

 

 

4

1.

Front bagger tube

3

 

 

 

2

2.

Lower bagger tube

0259

 

 

3.

1/4 x 50,8mm Carriage

 

 

 

Bolts

 

 

4.

1/4 Lock nut

 

 

5

3

2

7 6

8

02593

2

To Assemble Bagger

NOTE: For ease of assembly, you may wish to obtain the assistance of another person when putting the bagger to- gether.

•Holes in front bagger tube are at an angle. Place front bagger tube against lower bagger tube and check for proper hole alignment before assembling bolts.

•Assemble front and lower bagger tubes using four (4) 1/4 x 50,8mm carriage bolts and lock nuts supplied. Tighten securely.

•Slide front and lower bagger tube assembly into the bag- ger assemby.

•Assemble front and upper bagger tubes using four (4) 1/4 x 50,8mm carraige bolts and lock nuts supplied. Tighten securely.

•Slip all the vinyl bindings over the bagger tubes

•Slide the bagger dump handle through the hole in the bagger top, install the clevis pin and secure with retainer spring.

•Push cap over end of bagger dump handle.

NOTE: For future use, the clevis pin may be removed in order to use the handle to clear the chute in the event it has become

1. Front bagger tube

1

2.1/4 x 50,8mm Carriage Bolts

3.1/4 Lock nut

4.Vinyl Binding

5.Dump handle tube

6.Clevis pin

7.Retainer spring

8.Cap

2

3

4

6MM (1/4") - 9MM (3/8")

1

02329

clogged.

Bagger adjustment

For proper bag function and appearance, it may be neces- sary to adjust the bagger assembly. There should be 6mm (1/4")-9mm (3/8") gap between the bagger top and fender and the bagger top surface should be even with the top surface of the fender. To adjust bagger position:

Horizontal adjustment

•Slightly loosen the nuts securing the bagger RH and LH horizontal adjustment brackets. Loosen only enough so the brackets keep their position, but allow them to be moved.

•Move the brackets the amount forward or backward you wish the bag assembly to move. Retighten the nuts se- curely.

Vertical adjustment

1.Top Surfaces Even

2.Horizontal Adjustment Bracket

3.Vertical Adjustment Bracket

•Slightly loosen the nuts securing the vertical adjustment brackets. Loosen only enough so the brackets keep their position, but allow them to be moved.

•Move the brackets the amount up or down you wish the bag assembly to move. Retighten the nuts securely.

•Reinstall the bagger assembly and check the bagger to fender fi t. If necessary, repeat the procedure until proper fi t is attained.

To convert to bagging, mulching or discharge See "Section 5" of this manual.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Manuale di istruzioni Manuel d’instructionsAnleitungshandbuch InstructieboekjePage Training Safety RulesII.Preparation III. OperationIV. Maintenance and Storage Schulung SicherheitsvorschriftenII. Vorbereitung III. BetriebIV. Wartung UND Lagerung Précautions D’UTILISATION Règles de SécuritéII. Préparation III. UtilisationIV. Entretien ET Entreposage Instrucción Reglas De SeguridadII. Preparación III. OperaciónIV. Mantenimiento Y Almacenamiento Addestramento ALL’USO Norme AntinfortunisticheII. Preparazione III. FunzionamentoIV. Manutenzione E Periodi DI INATTIVITA’ Training VeiligheidsregelsII. Voorbereiding III. BedieningIV. Onderhoud EN Opslag EN8361997/A2Fast No Operation On Slopes More than Nicht AUF Abhängen MIT Züglich MIT Wasser Lenkrad Steering WheelVolante DE Dirección Volant DE DirectionVolante HET StuurSitz SeatSiège AsientoRemarque HinweisNota Curezza 3 sul supporto del sedileInstallazione della batteria Install batteryAccu installeren Einbau der BatteriePage Discharge Chute Nut Flat Washer To install bagger components to tractorHorizontal adjustment Bagger adjustmentVertical adjustment To Assemble BaggerAuswurfkanal Kontermutter 3/8 Flache unterlegscheibe Installation der Aufhängung der Grasfangbox des TraktorsJustieren der Grasfangbox Montage der GrasfangboxSeitenjustierung HöhenjustierungGoulotte déjection Ecrou 3/8 Rondelle plate Assemblage des composants du collecteurEpingle Rondelle plate diamPositionnement du collecteur Pour assembler le collecteurRéglage de la position horizontale Réglage de la position verticaleClavija hendida Descarga de adaptarse Tuercas de 3/8 Arandelas planasCuando éste se mueve en un terreno desigual Regulacion del contenedor Para montar el contenedorAjuste horizontal Ajuste verticalConvogliatore di scarico Dadi 3/8 Rondella Piatta Per montare i componenti del cesto di raccoltaCoppiglia Regolazione del cesto Per montare il cesto di raccoltaRegolazione orizzontale Regolazione verticaleBorgmoer 3/8 Vlakke sluitring Steun Afvoertrechter Borgmoer Vlakke sluitringSluitveer Vlakke sluitring 10,3 mmAfstellen van grascontainer De grascontainer monterenHorizontale bijstelling Verticale bijstellingMontage und Installation des Mulcheinsatzes To assemble and install mulcher plugPer Iinstallazione del Kit Mulching Het monteren en installeren van de mulchplugEinstellen DER Tasträder To Adjust Gauge WheelsReglage DES Roulettes DE Jauge Para Ajustar LAS Ruedas CalibradorasAnordnung der Bedienungseinrichtungen Positioning of controlsUbicación de los mandosè ComandiDe plaats van de bedieningsorganen Gashebel Commande des gazAcelerador AcceleratoreBrake and clutch pedal Levier de commande de la transmission hydrostatiqueBrems- und Kupplungspedal Pédale dembrayage et de freinQuick lifting/lowering of the cutting unit Elevación/descenso rápidos del equipo de corteSchnelles Heben und Senken des Mähaggre- gats Sollevamento/abbassamento del tagliaerbaCerradura de encendido ZündschloßChiave di accensione Clé de contact et de démarrageFreno de estacionamiento Frein de stationnementFreno di parcheggio Parkeerrem10. Mähhöheneinstellung Cutting height settingChoke control KaltstartreglerReposición de combustible Filling upTanken Plein de carburantÖlstand Oil levelNiveau d’huile Nivel de aceiteReifendruck Tire air pressurePression de gonflage des pneus Presión de inflado de los neumáticosDriving . Betrieb . Conduite . Conducción Guida . Rijden Page Hinweis ATTENZIONE! Avviamento a Freddo PER Trasmission IMPORTANT! Cold Starting for HydroBELANGRIJK! Loud Starten Voor Hydro Purge TransmissionSpurgo Della Trasmissione Purgar LA TransmisiónTransmissie Ontluchten Su tractor esta ahora dispuesto para la operación nor- malBetrieb DrivingConduite ConducciónRatschläge zum Rasenmähen Cutting tipsConseils pour la tonte Consejos para el corteEntleeren der Grasfangbox To Dump BaggerPour vider le bac Para vaciar la cargadoraPour passer dune fonction à une autre To convert mowerPour broyer Regolazione della funzione di taglio Para cambiar el ajuste de la segadoraDe Maaier Ombouwen Advertencia WarnungPericolo WaarschuwingAbstellen des Motors Switching off the engineArrêt du moteur Parada del motorWaarschuwing Motorhaube Engine hoodCapot moteur Cubierta del motorWartung MaintenanceEntretien MantenimientoPour assurer lentretien du moteur To service engineMantenimiento del motor Wartung des MotorsWartungsnachweis Service RecordInforme DE Servicio Schema DentretienDati DI Servizio Service AantekeningenMesserbalken BladesLames CuchillasMesserbalkenbohrung mit fünfeckige Ausspa- rung Star pattern bladeLame avec orifice de fixation central étoil à cinq branches Messerbalkenbohrung mit sechseckiger Aus- sparungLama con for stellare a 5 punte Cuchilla de orificio-estrella de cinco puntasMes met 5-hoekige ster Lama con foro stellareBlade Removal Bremse BrakesFrein FrenoDismantling of the cutting unit Assembly of the cutting unitDemontage des Mähdecks Depose du Carter de CoupeAuswechsein des Treibriemens für das Mähag- gregat Replacement of drive belt for cutting unitCambio de la correa propulsora del equipo de corte Sostituzione della cinghia di movimento lameEinstellung des Mähaggregats Adjustment of the cutting unitRéglage du carter de coupe Ajuste de la unidad de corteAdjuste DE Lado a Lado SIDE-TO-SIDE AdjustmentSeitliche Einstellung Reglage TransversalRemplacement de la courroie dentraînement Replacement of drive beltAuswechsein des Treibriemens Cambio de correa propulsoraReglage DU Levier DE LA Commande D’AVANCEMENT Transaxle Motion Control Lever Neutral AdjustmentEinstellung DES Steuerknüppels DES Schaltgetriebes Page TRANSACHSEN-KÜHLUNG Transaxle CoolingRefroidissement DE LA Transmission Enfriamiento DEL TransejeTroubleshooting . Störungssuche Recherche des pannes . Búsqueda de averías Ricerca guasti . Het localiseren van fouten Storage . Aufbewahrung . Remisage . Conservación ServiceEntretien et réparations ServicioServizio Rismessaggio . StallenPage Page 532 19 39-70 Rev 01.28.05 TR

CTH210xp, CTH150 XP specifications

The Husqvarna CTH150 XP and CTH210 XP are exceptional lawn tractors designed for efficient mowing and robust performance, making them ideal choices for homeowners and small property managers. Known for their innovative technologies and user-friendly features, these models stand out in the crowded market of riding mowers.

The CTH150 XP features a powerful 15 HP Kohler engine, providing ample power for tackling various lawn terrains. With its 42-inch cutting deck, this tractor ensures a wide and efficient cutting path, allowing users to cover more ground in less time. The CTH210 XP, on the other hand, is equipped with an even more robust 21 HP engine, paired with a 46-inch cutting deck, making it suitable for larger properties and tougher mowing conditions.

Both models come with Husqvarna's Pedal-operated transmission system, which allows for seamless speed adjustments while keeping hands free for steering. This feature promotes more control and a smoother mowing experience. Additionally, they incorporate a reinforced cutting deck construction that enhances durability and performance, ensuring that users can rely on their mower for years to come.

One of the standout technologies in both the CTH150 XP and CTH210 XP is the ClearCut™ cutting system. This advanced system delivers superior cutting performance by utilizing a deep deck design that improves grass flow, resulting in a better cut quality and even grass distribution. Users can choose from multiple cutting heights, adjusted easily from the operator's seat, to achieve the desired lawn appearance.

In terms of maintenance, both models are designed with hassle-free access to critical components, making routine checks and servicing straightforward. The large fuel tank allows for extended mowing sessions without frequent refueling stops, a significant advantage for larger lawns.

Comfort is also paramount in the design of the CTH150 XP and CTH210 XP. Featuring ergonomically designed seats, users can enjoy a comfortable ride even during extended mowing sessions. The control panel is strategically placed for easy access to vital functions, and the overall design ensures optimal visibility while mowing, enhancing safety and precision.

In summary, the Husqvarna CTH150 XP and CTH210 XP represent cutting-edge lawn tractor technology, combining powerful engines, durable construction, advanced cutting systems, and user-centric design. These models are perfect for anyone looking to achieve a well-manicured lawn efficiently and comfortably.
Top Page Image Contents