Samsung SCC-C4207P, SCC-C4307P manual 16

-C-LEVEL: It is used to set the levels for the Burst signal and the entire colour signal of the video signal.

-OTHER SET

In OTHER SET menu, you can adjust LANGUAGE, CTRL TYPE, ZOOM SPEED, D-ZOON, RS-485, SYSTEM INFO..., and V-SYNC function, etc. When you press [ENTER] key from OTHER SET menu, the OTHER SET additional menu screen appear.

(OTHER SET)				(RS-485)
LANGUAGE	ENGLISH
CTRL TYPE	A
ZOOM SPEED	4	Press the
D-ZOOM	OFF
			ENTER
RS-485	...
SYSTEM INFO ...			button.
				PROTOCOL	SAMSUNG
V-SYNC	INT
				BAUD RATE	9600
RET				ADDRESS	0
				RET

- SYSTEM INFO : You can confirm settings related to the

(SPECIAL)		(OTHER SET)
POSI/NEGA	+	LANGUAGE	ENGLISH
DIS	OFF	CTRL TYPE	A
REVERSE	OFF	ZOOM SPEED	4

RS-485 communication, product serial number, and the software version.

E

DETAIL	(0)--I-	D-ZOOM	OFF
Y-LEVEL	(0)I--------	RS-485	...
C-LEVEL	(0)I--------	SYSTEM INFO ...
OTHER SET	...	V-SYNC	INT
RET		RET

❖V-SYNC menu is only available in SCC-C4307.

-LANGUAGE : Selects English/French/German/Spanish/ Italian OSD menu.

-CTRL TYPE : By inputting the wire remote port, you may set up the mode, A, B, C, or D.

Code	Item	Tele	Wide	Far	Near
	A	-6V	+6V	+6V	-6V
		-6V	+6V	-6V	+6V
	B
	C	+6V	-6V	+6V	-6V
		+6V	-6V	-6V	+6V
	D

-ZOOM SPEED : Use [Left, Right] key in the ZOOM SPEED menu to set the speed as follows.

-ZOOM SPEED 1 : About 17Sec. from X 1 to X 32(Slowest)

-ZOOM SPEED 2 : About 10Sec. from X 1 to X 32(Slow)

-ZOOM SPEED 3 : About 6Sec. from X 1 to X 32(Fast)

-ZOOM SPEED 4 : About 3Sec. from X 1 to X 32(Fastest)

-D-ZOOM : Sets up the Digital Zoom magnification ratio up to x10.

-RS-485 : Sets up RS-485 Communication Protocol,

Address, and Baud Rate.

29

(OTHER SET)				(SYSTEM INFO)
LANGUAGE	ENGLISH			ROM VER	1.000
CTRL TYPE	A			EEP VER	1.000
ZOOM SPEED	4	Press the		PROTOCOL	SAMSUNG
D-ZOOM	OFF
			ENTER	ADDRESS	0
RS-485	...			TYPE	RS-485, HALF
SYSTEM INFO	...		button.	BAUD RATE	9600
V-SYNC	INT
				SERIAL NO	000000000000000
RET
				RET

-V-SYNC : INT shall be selected to use internal synchronization. LINE... is used to synchronize several camera phases for the multi camera operation by using an external signal(AC signal). As there may be a slight deviation between sets, adjusts PHASE to overcome this handicap. When you use AC power source, V-SYNC is available. Select LINE... and press [ENTER] and the PHASE control submenu will appear. The PHASE control ranges from -106H to +106H as for NTSC and from -138H to +138H as for PAL.

❖When a DC power is supplied, V-SYNC menu will be displayed as --- and you cannot make any settings.

(OTHER SET)				(LINE LOCK)
LANGUAGE	ENGLISH
CTRL TYPE	A
ZOOM SPEED	OFF	Press the
D-ZOOM	OFF
			ENTER
RS-485	...
SYSTEM INFO ...			button.
V-SYNC	LINE...
RET				PHASE	(-106)----I----
				RET
					30