Thermo Products OL6RA072DV5(B/R) manuals

Thermo Products OL6RA072DV5(B/R) Operation Manual

75 pages2.49 Mb

OIL FIRED FURNACE
- INSTALLATION AND OPERATION MANUAL WITH USERS INFORMATION SECTION
  - 2
  - 6A. CODES AND CLEARANCES:
  - 7B. MAKE-UP AIR:
  - 8 II. GENERAL INSTRUCTIONS - READ BEFORE START OF INSTALLATION
  - cWARNING: This furnace is not to be used as a construction heater.
  - A. CHIMNEY:
  - 9Qualified service personnel must perform all installations and services.
  - 103. PROPER CHIMNEY HEIGHT:
  - 4. PROPER VENT CONNECTOR PIPE/CHIMNEY CONNECTION:
  - 116. TIGHT JOINTS:
  - 7. TIGHT CLEAN-OUT DOORS AND CONNECTIONS:
  - 8. NO INTERCONNECTED CHIMNEY FLUES:
  - 9 FLUE PIPE CLEARANCES, SIZING AND TYPE:
  - 12REDUCTION OF CLEARANCES WITH SPECIFIED FORMS OF PROTECTION:
  - B. VENTING:
  - 13 c CAUTION MUST BE TAKEN NOT TO EXCEED 90 ROTATION (OF THE FLUE ELBOW) .
  - ROTATION OF FRONT FLUE ELBOW:
  - C. DRAFT REGULATORS:
  - 14D. DUCT WORK/AIR CONDITIONING:
  - Airflow Requirements and Sizing of Duct Work:
  - 18E. Air Filters Mounted Internal to Furnace:
  - 20G. BURNER INSTALLATION:
  - 21H. BURNER SPECIFICATIONS AND APPLICATIONS:
  - 23MOUNTING THE 2-STAGE RIELLO BURNER:
  - I. OIL TANK AND PIPING:
  - 25J. OIL FILTER:
  - K. ELECTRICAL WIRIING:
  - 26Electronic Air Cleaner (EAC) and Humidifier Installation:
  - 28Preferred method of adjustment:
    - 27
  - 30 Heating Speed Set-ups
  - - 28
    - Heating Speed Set-ups ( 2 Stage ) OL6*X072DV5
  - 31 = Recommended heating speed setting
  - 34 M. BLOWER CONTROLLER INFORMATION FOR PSC MOTOR
  - 37
  - Table 11: ON and OFF Blower Delay Time Switch Settings
  - 39N. STARTUP PROCEDURES:
  - Operating Instructions: i. ii. iii. iv.
  - v. vi. vii. viii.
    - For Your Safety Read Before Operating:
  - 41COMBUSTION HEAD SETTING FOR 2-STAGE RIELLO BURNER:
  - 42TURN TO THE RIGHT: (SIGN + )
  - TURN TO THE LEFT: (SIGN - )
  - AIR DAMPER ADJUSTMENT:
  - 431st STAGE ADJUSTMENT:
  - 2nd STAGE ADJUSTMENT:
  - 44NOTICE: Minimum temperature rise is 50F.; maximum temperature rise is 80F.
  - k.
  - l.
  - m.
  - n.
  - 3. Adjustment Of Heat Input Rate:
  - 45NOTICE: It may be necessary to bleed air from the oil line before the burner can be fired.
  - 4. Setting Supply Air Temperature Rise:
  - 48D. STARTING THE BURNER:
  - E. FILTER CLEANING AND LOCATION:
  - 49IV. INSTALLER'S INSTRUCTIONS TO USER:
  - 50V. DEALER MAINTENANCE:
  - A. GENERAL INSPECTION:
  - cWARNING: Shut off oil and disconnect power before continuing with this inspection.
  - 51B. HEAT EXCHANGER:
  - cWARNING: A qualified heating contractor must clean the heat exchanger.
  - C. HEAT EXCHANGER CLEANING INSTRUCTIONS:
  - cWARNING: THE HEAT EXCHANGER MUST BE CLEANED BY A QUALIFIED SERVICE PERSON.
  - 54Filter replacement:
  - G. EXTENDED APPLIANCE SHUTDOWN:
  - 58VII. TROUBLESHOOTING:
  - PERSONNEL, AND NOT BY THE FURNACE OWNER.
  - A. DIAGNOSTICS:
  - Diagnostic Features:
  - 59B. CAD CELL CHECKOUT PROCEDURE:
    - 67manual carefully before making tests. Retain this form with furnace.