Restoring the Factory Default Settings | 3Com Hub 1000 SX specs

Image 48

3Com Hub 1000 SX manual Restoring the Factory Default Settings, A-14 APPENDIX A USING THE CONSOLE PORT

Contents

SuperStack II Hub 1000 SX User GuideA member of the 3Com SuperStack II System 3Com Corporation 5400 Bayfront Plaza Santa Clara, California UNITED STATES GOVERNMENT LEGENDS CONTENTS 2 INSTALLING THE HUBABOUT THIS GUIDE 1 INTRODUCTION A USING THE CONSOLE PORT 3 MAKING CONNECTIONSPOST Messages SPECIFICATIONS GLOSSARY INDEX 3COM CORPORATION LIMITED WARRANTYTECHNICAL SUPPORT FCC CLASS A VERIFICATION STATEMENTPage FIGURES Page TABLES Port Conﬁguration MenuPage ABOUT THIS GUIDE IconNotice Type Description Commands SETDEFAULT !0 -IP NETaddr =Menu commands and buttons INTRODUCTION Hub 1000 SXGeneral Description Downlinks and UplinkFull-Duplex Operation Flow Control Features and Functions INSTALLING THE HUB SuperStack II Hub 1000 SX User Guide Hub Description The hub’s front and rear panels are shown in Figure Installing and Connecting the Hub 4 Repeat steps 2 and 3 for the other side of the hub Connector Table 2-1 Downlink ConnectionsMaximum Cable Type Table 2-2 Hub 1000 SX Indicators IndicatorColor Status Connecting a GBIC ModuleThe gigabit interface connector GBIC port on the rear panel of the Using Optional Power Systems Power Modules Cabling Options A hub connects to a UPS unit through the hub’s AC power cord Table 2-4 Advanced RPS Conﬁguration Options You can connect a UPS unit to an Advanced RPS unit as long as you do not exceed the maximum wattage 325 watts for the UPS unit. To verify that the UPS unit’s maximum wattage is not exceeded, calculate the total power consumption of all units connected to the Advanced RPS. If the result is less than 325 watts, your conﬁguration is safe if the result is greater than 325 watts, then there are too many units connected to the Advanced RPS Page MAKING CONNECTIONS Table 3-1 Gigabit Ethernet Maximum Cable Lengths Power Workgroup AggregatingServers connecting to the network backbone. See Figure Switches The Hub 1000 SX does not support bandwidth aggregation trunkingYou can use the Hub 1000 SX downlinks to aggregate 10/100 Mbps Figure 3-3 Aggregated Switches Connection 3-4 CHAPTER 3 MAKING CONNECTIONS Connecting Figure 3-4 Mixed ConnectionThe best use of the hub uplink is as a backbone connection to a 3Com Figure 3-6 Uplink Connection to a 10/100 Mbps Switch Table 3-2 Troubleshooting TipsSymptom Solution USING THE CONSOLE PORT Connecting the With PowerRequirements Console Port from power To connect the console port when the hub is disconnectedConnecting the Console Port A-3 Disconnected Logging On message, return the hub to the supplierAfter 4 minutes of inactivity, the CLI logs off automatically Password Port SettingsChanging the Conﬁguring To display the Port Conﬁguration menu Configuring Port Settings Table A-2 Port Conﬁguration Menu A-8 APPENDIX A USING THE CONSOLE PORT Configuring Port Settings and be conﬁgured to receive pause frames Configuring Port Settings A-11 Displaying Hub Statusmatrix, Y indicates yes and n indicates no. See Table A-3 Table A-3 Hub Status Information Displaying Hub Status A-13 Restoring the Factory Default Settings A-14 APPENDIX A USING THE CONSOLE PORT Updating the Firmware Imageentering option Checking the Xmodem-CRC To transfer the ﬁrmware image ﬁle during a ﬁrmware update, the CLI displays the following message Logging Offlog in again. To restart the ﬁle transfer, repeat steps 6 and Table A-4 File Transfer Error Messages Table A-5 Fatal Error MessagesWhile saving port settings or SPECIFICATIONS Physical DimensionsEnvironmental Operating Ranges Page Services Board ServiceTECHNICAL SUPPORT Online Technical Access by Analog Modem Access by Digital Modem1 408 654 C-2 APPENDIX C TECHNICAL SUPPORT Local access numbers are available within the following countries Santa Clara, California Czech Republic/SlovakCentral European HQ 305 261 3266 Miami, Florida To obtain an RMA number, call or fax Page GLOSSARY Carrier Sense Multiple Access/Collision Detection. Channel access cable is based on CSMA/CD Carrier Sense Multiple Access/Collisionaccess method transmission of light signals IEEE incomingﬂow control Mbps control. See also asymmetric ﬂow control, ﬂow control, pause frame Symbols INDEXNumbers Page Switch 9300 3-2, 3-3 Page 3Com Corporation LIMITED WARRANTY STANDARD WARRANTY SERVICEHARDWARE SOFTWARE FCC CLASS A VERIFICATION STATEMENT LIMITATION OF LIABILITYGOVERNING LAW