Manuals / 3M / Kitchen Appliance / Food Saver

3M 200a Adjustments, could result Box Drive Belt Tension, 1 - Box Drive Belt Tension Adjustment

Models: 200a

1 62

Download 62 pages 54.72 Kb

Page 24

Adjustments

Adjustments

WARNING – Turn off electrical power supply and disconnect power cord from electrical supply before beginning adjustments. If power cord is not disconnected, severe injury to personnel

could result.

Box Drive Belt Tension

The two continuously moving drive belts convey boxes through the tape applying mechanism. The box drive belts are powered by an electric gear motor.

Tension adjustment of these belts may be required during normal operation. Belt tension must be adequate to positively move the box through the machine and the belts should run fully on the surface of the pulleys at each end of the frame. The idler pulleys on the infeed end are adjusted in or out to provide proper belt tension. Each belt is adjusted separately.

Belt tension is obtained by tightening the adjustment screw so that a moderate pulling force of 3.5 kg [7.5 lbs.] applied at the midspan, as shown in Figure 5-1, will deflect the belt 25 mm [1 inch]. This will assure positive contact between the belt and the drive pulley on the discharge end of the taping head.

Figure 5-1 – Box Drive Belt Tension Adjustment

19

Image 24

3M 200a manual Adjustments, could result Box Drive Belt Tension, 1 - Box Drive Belt Tension Adjustment

Contents

Instructions and Parts List AdjustableImportant Safety Information 3M-MaticReplacement Parts and Service Information To Our Customers3M/Tape Dispenser Parts 241 Venture DriveReplacement Parts And Service Information To Our Customers3M Center, Building 220-8W-01 St. Paul, MN 55144-1000 1-800/328 Table of Contents 200a, Adjustable Case Sealer, TypeSection I - 200a Adjustable Case Sealer PageAdjustments Special Set-Up ProcedureTroubleshooting Electrical DiagramDescription Contents - 200a Adjustable Case Sealer Important Safeguards Important Safeguards Continued Figure 1-8 - Up/Down/Lock Label Specifications 1. Power Requirements2. Operating Rate 3. Operating ConditionsSpecifications Continued Specifications Continued Installation and Set-Up Receiving And HandlingMachine Set-Up WARNING - Follow this step carefully as spring pressure isFigure 2-1 - 200a Frame Set-Up CAUTION - Machine weighs approximately 123 kg 280 pounds uncratedInstallation and Set-Up Continued WARNING - To prevent shock and fire hazard Position extension cord Operation Figure 3-1 - 200a Case Sealer Components Left Front ViewOperation Continued WARNINGSBox Size Set-Up Figure 3-2 - Upper Taping Head Figure 3-3 - Upper Taping HeadFigure 3-4 - Side Guides Figure 3-5 - Check Adjustments Figure 3-6 - Compression Rollers will occurBox Sealing Maintenance CleaningLubrication Figure 4-1 - Lubrication Points - FrameMaintenance Continued Knife Replacement, Taping HeadBox Drive Belt Replacement Figure 4-2 - Box Drive Belt ReplacementAdjustments Figure 5-1 - Box Drive Belt Tension Adjustmentcould result Box Drive Belt Tension Adjustments Continued Figure 5-2 - Box Drive Belt Tension Adjustment Machine Bed Infeed Endcould result personnel could result Taping Head Adjustments - Refer to Section THIS PAGE IS BLANK Special Set-Up Procedure personnel could result Changing the Tape Leg LengthFigure 6-1 - Case Sealer Frame Changes Special Set-Up Procedure Continued Special Set-Up Procedure Continued Figure 6-2 - Box and Machine Bed Height RangeTHIS PAGE IS BLANK Troubleshooting Troubleshooting GuideProblem CausePage Electrical Diagrams Continued Electrical Diagrams Continued Replacement Parts and Service Information Options/Accessories Replacement Parts - Illustrations and Parts Lists To Order PartsTHIS PAGE IS BLANK 200a Adjustable Case Sealer Frame Assemblies 200a Adjustable Case Sealer Figure 2795/1 of Ref. No 3M Part NoDescription 200a Adjustable Case Sealer Figure 2795/2 of Ref. No 3M Part NoDescription 200a Adjustable Case Sealer Ref. No 3M Part NoDescription 200a Adjustable Case Sealer Ref. No 3M Part NoDescription 200a Adjustable Case Sealer Ref. No 3M Part NoDescription 200a Adjustable Case Sealer Ref. No 3M Part NoDescription 200a Adjustable Case Sealer Ref. No 3M Part NoDescription 200a Adjustable Case Sealer Ref. No 3M Part NoDescription Page Ref. No 3M Part NoDescription 200a Adjustable Case Sealer Ref. No 3M Part NoDescription 200a Adjustable Case Sealer Safety and Information LabelsSafety and Information Labels Ref. No