Installation and Set-Up (Continued)

11.Box size capacity (height) – at its factory setting, the case sealer handles box sizes up to 620 mm [24-1/2 inches] maximum height. If larger capacity is needed, the machine can be adjusted to accommodate up to 725 mm [28-1/2 inches] high boxes. Refer to "Special Set-Up Procedure – Outer Column Re-Positioning", for set-up information.

12.Drive Belt Height – drive belt assemblies can be raised 50 mm [2 inches] to provide better conveying of tall boxes. Refer to "Special Set- Up Procedure – Changing Drive Belt Height".

13.Pneumatic connection.

depressed and that all packaging materials and tools are removed from the machine. Do not plug electrical cord into outlet until ready to run machine.

Note Machines outside the U.S. may be equipped with 220/240 Volt, 50 Hz systems, or other electrical requirements compatible with local practice.

WARNING

To reduce the risk associated with mechanical and electrical hazards:

Turn electrical and air supply off and disconnect before performing any adjustments, maintenance or servicing the machine or taping heads

The case sealer requires a 6.5 bar gauge pressure [95 PSIG] 75 liter/min @21°C, 1.01 bar [2.5 SCFM] compressed air supply. As shown in Figure 2-5 an on/off valve, pressure regulator, and filter are provided to service the air supply.

The main air supply line should be connected to the on/off valve by means of the barbed fitting and hose clamp provided on the outer side of the on/off valve as shown in Figure 2-5. The customer supplied air hose (5/16 inch [8 mm] ID) should be slipped over the barbed fitting and clamped tightly in place.

If another type of connector is desired, the fitting can be removed and replaced with the desired 1/4-18 NPT threaded connector.

Always turn the valve "Off" when air supply line is being connected or disconnected.

14.Electrical connection and controls – the electrical control box shown in Figure 3-1, contains the "On/Off" switch with pre-set breaker and can be located on either side of the machine frame for operator convenience. A standard three conductor power cord with plug is provided at the back of the electrical control box for 115 Volt, 60 Hz, 3.8 Amp electrical service. The receptacle providing this service shall be properly grounded. Before the power cord is plugged into 115 Volt, 60 Hz outlet, make sure red "Off" button is

Initial Start-Up of Case Sealer

After completing the "Set-Up" procedure, continue through ""Operation", to be sure case sealer is properly adjusted to run product.

Figure 2-5 – Pneumatic Connection

15

Page 23
Image 23
3M 800af-s manual Initial Start-Up of Case Sealer, Pneumatic Connection

800af-s specifications

The 3M 800AF-S is an advanced particle filter that is widely recognized for its efficiency and adaptability in various industrial and occupational settings. Designed to combat particulate contaminants in the workplace, this filter exemplifies 3M’s commitment to innovation and safety.

One of the key features of the 3M 800AF-S is its exceptional particle filtration capability. It is engineered to capture a wide range of airborne particles, including dust, pollen, mold spores, and even some bacteria and viruses, making it a vital tool for industries such as healthcare, construction, and manufacturing.

The filter utilizes a unique electrostatic media technology that enhances its particle capture efficiency. This technology allows the filter to attract and trap smaller particles that might otherwise pass through conventional filters. With a high filtration efficiency rating, the 3M 800AF-S ensures that users are protected from harmful respiratory hazards.

Another noteworthy characteristic of the 3M 800AF-S is its low breathing resistance. This feature is crucial for maintaining comfort during extended wear, particularly in environments where workers may be required to wear a respirator for long hours. The low breathing resistance is achieved through an optimized design that balances the filter’s density and porosity, ensuring airflow without compromising on safety.

The 3M 800AF-S is also compatible with a range of 3M respirators, providing versatility for users across various applications. The easy-to-use design allows for quick attachment and detachment, ensuring that the filter can be replaced efficiently and conveniently when needed.

Furthermore, the 3M 800AF-S is equipped with a durable outer layer that enhances its lifespan and performance in challenging environments. This durability ensures that the filter maintains its integrity even under rigorous use, which is particularly beneficial in industrial settings where exposure to harsh conditions is common.

In summary, the 3M 800AF-S stands out in the market due to its superior filtration efficiency, low breathing resistance, compatibility with various respirators, and robust construction. As industries continue to prioritize worker safety, filters like the 3M 800AF-S are essential for ensuring a safer and healthier working environment.