Manuals / 3M / Kitchen Appliance / Food Saver

3M 800af-s Maintenance Continued, Air Line Filter – Figure, Circuit Breaker, 5– Air Line Filter

Models: 800af-s

1 98

Download 98 pages 20.27 Kb

Page 37

Air Line Filter – Figure 4-5

Maintenance (Continued)

WARNING

•To reduce the risk associated with mechanical and electrical hazards:

–Turn electrical and air supply off and disconnect before performing any adjustments, maintenance or servicing the machine or taping heads

Air Line Filter – Figure 4-5
Periodically check the air line filter to drain water and
clean as necessary. Do not allow water to go above
the filter element.
Circuit Breaker
The case sealer is equipped with a circuit breaker
which trips if the motors are overloaded. Located
inside the electrical control box on the side of the
machine, the circuit breaker has been pre-set at
2.2 Amps and requires no further maintenance.
WARNING
• To reduce the risk associated with
mechanical and electrical hazards:
– Allow only properly trained and qualified
personnel to operate and/or service this
equipment
If circuit is overloaded and circuit breaker trips,	Figure 4-5 – Air Line Filter
If circuit is overloaded and circuit breaker trips,
unplug machine from electrical power:

1. Determine cause of overload and correct.

2. Remove electrical enclosure cover.

3. Press the red "Reset" button and then the green "Start" button.

4. Replace cover.

5. Plug in machine. Wait two minutes.

6. Press machine "On" button, on the side guard, to resume case sealing.

Knife Replacement, Taping Head

See Section II, "Maintenance – Blade (Knife)

Replacement".

29

Image 37

3M 800af-s manual Maintenance Continued, Air Line Filter – Figure, Circuit Breaker, • To reduce the risk associated with

Contents

Instructions and Parts List Stainless Steel Adjustable Case Sealer withImportant Safety Information 3M-MaticPage Replacement Parts and Additional Manuals Replacement Parts and Service InformationTo Our Customers Technical AssistancePage SERVICE,REPLACEMENTPARTSANDADDITIONALMANUALS Replacement Parts And Service InformationTo Our Customers AVAILABLE DIRECT FROMPage Instruction Manual Table of ContentsPage Page Table of Contents ContinuedSection I – AccuGlide SST 2 Inch Taping Heads Intended Use 1Tool/Spare Parts Kit Explanation of Signal Word Consequences Important Safeguards•To reduce the risk associated with muscle strain •To reduce the risk associated with pinch hazardsFigure 1-1– Replacement Labels/3M Part Numbers Important Safeguards ContinuedPage Operator Skill Level Descriptions Important Safeguards ContinuedSkill 1 - Machine Operator Operation1.Power Requirements Specifications2.Operating Rate 3.Operating Conditions Specifications Continued4.Tape 5.Tape Width9.Box Weight and Size Capacities Specifications ContinuedBOX LENGTH IN DIRECTION OF SEAL MUST BE GREATER THANDimensions are listed on the following page Specifications ContinuedMinimum 10.Machine DimensionsMaximum MinimumReceiving And Handling Installation and Set-UpMachine Set-Up •To reduce the risk associated with muscle strainFigure 2-1– Installation and Set-Up Installation and Set-Up ContinuedFigure 2-2– Lower Tape Drum Bracket Position Figure 2-4– Conveyor Bed Height Adjustment Installation and Set-Up ContinuedFigure 2-3– Conveyor Systems Initial Start-Upof Case Sealer Installation and Set-Up ContinuedFigure 2-5– Pneumatic Connection Operation 1Electrical On/Off Switch Figure 3-2– Controls, Valves and SwitchesOperation Continued 4Height Adjustment Crank, Upper Taping Head 3Emergency Stop Switch5Width Adjustment Crank 7Indicator, Air PressureTape Loading/Threading – Upper Taping Head Operation ContinuedTape Loading/Threading – Lower Taping Head With Tape Drum On Taping HeadBox Size Set-Up Figure Operation ContinuedMove the compression rolls as wide as possible Figure 3-6– Box Size Set-UpFigure Operation ContinuedFigure Figure 3-7– Box Size Set-UpFigure Operation ContinuedFigure •To reduce the risk associated with pinch hazardsFigure Operation ContinuedFigure Figure 3-11– Box Size Set-UpFigure Operation ContinuedBox Sealing Figure 3-13– Box Size Set-UpOperation Continued 7.Turn machine On only when it is safe to do soBox Jams •To reduce the risk associated with muscle strainCleaning MaintenanceLubrication Figure 4-1– Lubrication Points, FrameDrive Belt Replacement/Tension Adjustment Maintenance ContinuedFigure 4-2– Drive Belt Replacement Figure Figure11.Assembly is reverse of disassembly Maintenance ContinuedKnife Replacement, Taping Head Maintenance ContinuedAir Line Filter – Figure Circuit BreakerGate Operation Taping Head Adjustments – Refer to SectionDrive Belt Tension Figure 5-1– Gate CamsUpper Taping Head Leveling Adjustments ContinuedFigure 5-2– Upper Taping Head Leveling Gate Stroke Setting Adjustments ContinuedFigure 5-4– Gate Stroke Setting Gate Pressure RegulatorTHIS PAGE IS BLANK Figure 6-1– Drive Belt Height, Disassembly Special Set-UpProcedureFigure 6-2– Drive Belt Height, Reassembly Changing Drive Belt HeightOuter Column Re-Positioning Refer to Figure Special Set-UpProcedure Continued•To reduce the risk associated with muscle strain Figure 6-4– Column Re-Positioning Special Set-UpProcedure ContinuedTroubleshooting Guide TroubleshootingProblem CauseTroubleshooting Guide Troubleshooting ContinuedProblem CauseFigure 7-1– Pneumatic Diagram Pneumatic DiagramFigure 7-2– Electrical Diagram Electrical DiagramPage THIS PAGE IS BLANK Spare Parts Spare and Miscellaneous PartsRef. No Part NumberOption/Accessory Options/AccessoriesPart Number Frame Assemblies Replacement Parts – Illustrations and Parts ListsTHIS PAGE IS BLANK 800af Adjustable Case Sealer Frame Assemblies 800af-sAdjustable Case Sealer Figure Ref. No Figure3M Part No Description800af-sAdjustable Case Sealer Figure Ref. No Figure3M Part No Description800af-sAdjustable Case Sealer Figure Ref. No. 3M Part No FigureDescription 800af-sAdjustable Case Sealer Figure Ref. No. 3M Part No FigureDescription 10467-1800af-sAdjustable Case Sealer Figure 10473/1 of Ref. No Figure 10473 Page 1 of3M Part No Description800af-sAdjustable Case Sealer Figure 10473/2 of Ref. No Figure 10473 Page 2 of3M Part No DescriptionFigure 800af-sAdjustable Case SealerRef. No Figure3M Part No Description800af-sAdjustable Case Sealer Figure Code FigureDescription 10469-1800af Adjustable Case Sealer Figure Code FigureDescription 10470-1800af-sAdjustable Case Sealer Figure 10471/1 of Ref. No Figure 10471 Page 1 of3M Part No Description800af-sAdjustable Case Sealer Figure 10471/2 of Ref. No Figure 10471 Page 2 of3M Part No Description800af-sAdjustable Case Sealer Figure 10471/3 of Ref. No Figure 10471 Page 3 of3M Part No Description800af-sAdjustable Case Sealer Figure 10471/4 of Ref. No Figure 10471 Page 4 of3M Part No Description800af-sAdjustable Case Sealer Figure Ref. No Figure3M Part No Description800af-sAdjust able Case Sealer Figure 10472/1of Ref. No Figure 10472 Page 1 of3M Part No Description800af-sAdjustable Case Sealer Figure 10472/2 of Ref. No Figure 10472 Page 2 of3M Part No Description800af-sAdjustable Case Sealer Figure Ref. No FigureCode Description800af Adjustable Case Sealer Figure Ref. No Figure 10475 Page 1 of3M Part No DescriptionRef. No Figure 10475 Page 2 of3M Part No DescriptionTHIS PAGE IS BLANK 800af-sAdjustable Case Sealer Figure Ref. No Figure3M Part No DescriptionFigure 800af-sAdjustable Case SealerRef. No Figure3M Part No DescriptionTHIS PAGE IS BLANK