3M X66 1. , 2.

3

Fastening the lens cover

To avoid losing the lens cover, please fasten the

lens cover to the projector using the enclosed strap.

1.

Fix the strap to the strap hole of the lens cover.

Thread one end of the strap through the strap hole

of the lens cover and make the loop at the end, and

let the other end of the strap through the loop. Not

have a knot in the strap at either end.

2.

Fix the strap to the strap hole of the projector.

Thread the other end of the strap through the strap hole of the projector and make

the loop there. Let the lens cover with the one end of strap though the loop.

Projector features / Preparations

Projector features

This projector has a capability to project various picture signals onto a screen.

This projector requires only a minimal amount of space for installation and can

produce a large projected image from even a short distance.

This projector boasts a variety of I/O por and low noise. These features provide

you with the broad use of this projector.

Preparations

Contents of package

Your projector should come with the items shown below. Contact immediately your

dealer if anything is missing.

NOTE • Keep the original packing materials for future reshipment. For

moving the projector, be sure to use the original packing materials. Use special

caution for the lens part.

Projector

Remote control

(with two AA batteries)

Power cord VGA cable

Operator's Guide

Product Safety Guide

Quick Start Guide

Warranty and

Warranty Registration

WEEE Statement

Lens cover and Strap

Lens cover is attached to

the projector. Security Label

RCA

Video/Audio cable

Soft case

HOME

PAGE UP

PAGE DOWN

END

VIDEO SEARC

STANDBY/ON

H

FREEZE

MAGNIFY

ASPECT AUTOBLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

ESC

ENTER

MENU

RESET

COMPUTER

RCA

Component cable

USB cable

Contents

Main Digital Projector X66 Operator's Guide About this manual Content Fastening the lens cover 1. 2. Projector features Preparations Contents of package Part names Projector Control panel Rear panel Remote control Setting up Install the projector according to the environment and manner the projector will be used in. On a horizontal surface Suspended from the ceiling Arrangement Page Page Connecting your devices Connecting your devices (continued) Connecting power supply 1. 2. Using the security bar and slot Putting batteries 1. 2. 3. Remote control About the remote control signal Using as a simple PC mouse & keyboard Changing the frequency of remote control signal NOTE Turning on the power 1. 2. 3. CAUTION A strong light is emitted when the projectors power is on. Do Power on/off 1. 2. 3. Selecting an input signal 1. Adjusting the volume 2. Temporarily muting the sound 1. Operating Searching an input signal 1. Selecting an aspect ratio 1. Adjusting the zoom and focus 1. 2. Adjusting the projector's elevator 1. 2. 3. 4. 5. Adjusting the position 1. 2. Using the automatic adjustment feature 1. Using the magnify feature 1. 2. Correcting the keystone distortions 1. 2. Temporarily blanking the screen 1. Freezing the screen 1. 1. 2. 4. 3. Using the menu function 2. 3. 4. 5. EASY MENU EASY MENU (continued) PICTURE Menu PICTURE Menu (continued) To adjust CUSTOM function in GAMMA and COLOR TEMP PICTURE Menu (continued) IMAGE Menu From the IMAGE menu, items shown in the table below IMAGE Menu (continued) INPUT Menu Page INPUT Menu (continued) SETUP Menu From the SETUP menu, items shown in the table below SETUP Menu (continued) SCREEN Menu From the SCREEN menu, items shown in the table below Page Page Page OPTION Menu Page Page Page Page 1. Using Security Features 1.1 Inputting the PASSWORD 1.2 Changing the PASSWORD (continued) 1.3 If you have forgotten your PASSWORD 2. Using the MyScreen PASSWORD Function 2.1 Turning on the MyScreen PASSWORD Function 2.2 Setting the PASSWORD 3. Using the PIN LOCK Function Page (continued) 4. Using the Transition Detector Function 4.1 Turning On the Transition Detector Function 4.2 Setting the Transition Detector PASSWORD Page Maintenance Lamp 1. Turn the projector off, and unplug the power cord. 2. 3. 4. 5. 6. 7. Lamp warning HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE 1. 2. 3. 4. 5. 1. 2. 1. 2. Other care Troubleshooting Related messages Regarding the indicator lamps The projector is in a standby state. The projector is warming up. The projector is in an on state. The projector is cooling down. Shutting the projector down Resetting all settings Phenomena that may be easy to be mistaken for machine defects Phenomena that may be easy to be mistaken for machine defects (continued) Specications Specication Item Specication