3M X66 Part names Projector

4

Part names

Part namesProjector

(1) Lamp door (51)

The lamp unit is inside.

(2) Focus ring (18)

(3) Zoom ring (18)

(4) Control panel (5)

(5) Elevator buttons (x 2) (18)

(6) Elevator feet (x 2) (18)

(7) Remote sensor (13)

(8) Lens (18, 54)

(9) Lens cover (3)

(10) Intake vents

(11) Filter cover (53)

The air lter and intake vent are

inside.

(12) Speaker (35)

(13) Exhaust vent

(14) AC inlet (12)

(15) Power switch (15)

(16) Rear panel (5)

(17) Security bar (12)

(18) Security slot (12)

WARNING ►HOT! : Do not touch around the lamp door and the exhaust

vents during use or just after use, since it is too hot.

CAUTION ►

Maintain normal ventilation to prevent the projector from heating

up. Do not cover, block or plug up the vents. Do not place anything that can stick or

be sucked to the vents, around the intake vents. Clean the air lter periodically.

►Do not handle the elevator buttons without holding the projector, since the

projector may drop down.

►Do not look into the lens or vents while the lamp is on, since the strong light

is not good for your eyes.

HOT! (1) (2) (3) (4)

(7)

(10)

(9)

(8) (11)

(6)

(5)

HOT! (13)

(12)

(6)

(6)

(6)

(18)

(16)

(17)

(15)

(14)

(4)

(13)

(1)

(10)

(11)

Contents

Main Digital Projector X66 Operator's Guide About this manual Content Fastening the lens cover 1. 2. Projector features Preparations Contents of package Part names Projector Control panel Rear panel Remote control Setting up Install the projector according to the environment and manner the projector will be used in. On a horizontal surface Suspended from the ceiling Arrangement Page Page Connecting your devices Connecting your devices (continued) Connecting power supply 1. 2. Using the security bar and slot Putting batteries 1. 2. 3. Remote control About the remote control signal Using as a simple PC mouse & keyboard Changing the frequency of remote control signal NOTE Turning on the power 1. 2. 3. CAUTION A strong light is emitted when the projectors power is on. Do Power on/off 1. 2. 3. Selecting an input signal 1. Adjusting the volume 2. Temporarily muting the sound 1. Operating Searching an input signal 1. Selecting an aspect ratio 1. Adjusting the zoom and focus 1. 2. Adjusting the projector's elevator 1. 2. 3. 4. 5. Adjusting the position 1. 2. Using the automatic adjustment feature 1. Using the magnify feature 1. 2. Correcting the keystone distortions 1. 2. Temporarily blanking the screen 1. Freezing the screen 1. 1. 2. 4. 3. Using the menu function 2. 3. 4. 5. EASY MENU EASY MENU (continued) PICTURE Menu PICTURE Menu (continued) To adjust CUSTOM function in GAMMA and COLOR TEMP PICTURE Menu (continued) IMAGE Menu From the IMAGE menu, items shown in the table below IMAGE Menu (continued) INPUT Menu Page INPUT Menu (continued) SETUP Menu From the SETUP menu, items shown in the table below SETUP Menu (continued) SCREEN Menu From the SCREEN menu, items shown in the table below Page Page Page OPTION Menu Page Page Page Page 1. Using Security Features 1.1 Inputting the PASSWORD 1.2 Changing the PASSWORD (continued) 1.3 If you have forgotten your PASSWORD 2. Using the MyScreen PASSWORD Function 2.1 Turning on the MyScreen PASSWORD Function 2.2 Setting the PASSWORD 3. Using the PIN LOCK Function Page (continued) 4. Using the Transition Detector Function 4.1 Turning On the Transition Detector Function 4.2 Setting the Transition Detector PASSWORD Page Maintenance Lamp 1. Turn the projector off, and unplug the power cord. 2. 3. 4. 5. 6. 7. Lamp warning HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE 1. 2. 3. 4. 5. 1. 2. 1. 2. Other care Troubleshooting Related messages Regarding the indicator lamps The projector is in a standby state. The projector is warming up. The projector is in an on state. The projector is cooling down. Shutting the projector down Resetting all settings Phenomena that may be easy to be mistaken for machine defects Phenomena that may be easy to be mistaken for machine defects (continued) Specications Specication Item Specication