Manuals / Abit / Computer Equipment / Computer Hardware

Abit IS-20, IS-12, IS-10, IS-11 user manual

Models: IS-12 IS-10 IS-11 IS-20

1 56

Download 56 pages 30.77 Kb

Page 29

When set to [Auto], the BIOS will automatically check what kind of IDE drive you are using. If you want to define your own drive by yourself, set it to [Manual] and make sure you fully understand the meaning of the parameters. Refer to the manual provided by the device manufacturer to get the settings right.

BIOS Setup	3-3

IDE Channel 1 Master/Slave, IDE Channel 2 Master/Slave

Click <Enter> key to enter its submenu:

IDE HDD Auto-Detection

This item allows you to detect the parameters of IDE drives by pressing the <Enter> key. The parameters will automatically be shown on the screen.

IDE Primary Master

When set to [Auto], the BIOS will automatically check what kind of IDE drive you are using. If you want to define your own drive by yourself, set it to [Manual] and make sure you fully understand the meaning of the parameters. Refer to the manual provided by the device manufacturer to get the settings right.

Access Mode

This item selects the mode to access your IDE devices. Leave this item to its default [Auto] settings to let BIOS detects the access mode of your HDD and makes decision automatically.

Capacity

This item automatically displays your HDD size. Note that this size is usually slightly greater than the size given by a disk-checking program of a formatted disk.

NOTE: The following [Cylinder], [Head], [Precomp], [Landing Zone], and [Sector] items are available when you set the item “IDE Primary Master” to “Manual”.

User’s Manual

Image 29

Abit IS-20, IS-12, IS-10, IS-11 user manual

Contents

4200-0383-03 Rev IS-10/IS-11/IS-12/IS-20Intel Pentium 4 System Board Socket User’s Manual Copyright and Warranty Notice Chapter Hardware SetupIntroduction Table Of ContentsAppendix A. How to Get Technical Support Driver InstallationBIOS Setup ChapterChapter 1. Introduction 1.1. Features & SpecificationsExternal I/O Connectors Internal I/O ConnectorsMiscellaneous ChapterUser’s Manual 1.2. LayoutIntroduction 1.3. Jumpers & Connectors Description 2.1. Install The Motherboard Chapter 2. Hardware Setup2.2. Install Pentium 4 CPU and Heatsink Supporting-Base 2.3.1. Memory Configuration Table 2.3. System Memory2.3.2. Installing and Removing Memory Modules 2.4.1. ATX Power Connectors 2.4. Connectors, Headers, and Switches2.4.2. FAN Power Connectors Pin 1-2 shorted default Normal operation Hardware Setup2.4.3. CMOS Memory Clearing Header This header uses a jumper cap to clear the CMOS memoryIS-10 / IS-11 / IS-12 / IS-20 This slot supports an optional AGP graphics card up to AGP 4X/8X mode2.4.4. AGP Display Card Slot IS-10/IS-11/IS-12 2.4.5. Front Panel Switches & Indicators Connection Headers 2.4.6. Front Panel Audio Connection Header 2.4.7. Additional USB Port Connection Headers Hardware Setup2-11 These headers each provide two additional USB port connectionsIS-10 / IS-11 / IS-12 / IS-20 2.4.8. System Management Bus Connection HeaderThis header provides one additional System Management Bus connection 2.4.9. Additional IEEE1394 Port Connection Headers IS-12 IS-10 / IS-11 / IS-12 / IS-20 2.4.10. Internal Audio Source Connectors2.4.11. Floppy and IDE Disk Drive Connectors IS-10 / IS-11 / IS-12 / IS-20 2.4.12. Serial ATA ConnectorsThese connectors each provide one Serial ATA channel connection This header uses a jumper to adjust the CPU core voltage Hardware SetupPin 1-2 shorted default Normal operation 2.4.13. CPU Core Voltage Selector2.4.14. External I/O Panel Connectors Press DEL to run setup Chapter 3. BIOS SetupDate mmddyy 3.1. Standard CMOS FeaturesTime hhmmss IS-10 / IS-11 / IS-12 / IS-20When set to Auto, the BIOS will automatically check what kind of IDE drive you are using. If you want to define your own drive by yourself, set it to Manual and make sure you fully understand the meaning of the parameters. Refer to the manual provided by the device manufacturer to get the settings right Cylinder This item configures the numbers of cylinders Head No Errors The system-boot will not stop for any error detected BIOS SetupBase Memory Extended Memory3.2. Advanced BIOS Features Page 3.3. Advanced Chipset Features This option enables or disables the on-chip VGA controller BIOS SetupAGP Aperture Size Init Display FirstOnboard IDE Device 3.4. Integrated PeripheralsThis item enables or disables the onboard IDE-1 controller BIOS SetupThis item enables or disables the onboard IDE-2 controller SATA Only The SATA is operating in legacy modeIS-10 / IS-11 / IS-12 / IS-20 Serial ATA Port1 Mode / Serial ATA Port2 ModeOnboard PCI Device SuperIO Device KB Power ON Password BIOS SetupHot Key Power ON This item enables or disables the onboard FDD controllerParallel Port Mode This item specifies the parallel port mode 3.5. Power Management Setup Wake-Up by PCI card/LAN 3.6. PnP/PCI Configurations This item sets each system interrupt to either PCI Device or Reserved IRQ Resources Click Enter key to enter its submenuIS-10 / IS-11 / IS-12 / IS-20 3-203.7. PC Health Status 3.9. Load Optimized Defaults 3.8. Load Fail-Safe Defaults3.10. Set Supervisor Password 3.11. Set User PasswordUser’s Manual Chapter 4. Driver InstallationDriver Installation 4.1. Setup Items How to Get Technical Support Appendix A. How to Get Technical Supportsold the product to you first User’s Manualalt.comp.periphs.mainboard.abit comp.sys.ibm.pc.hardware.chips Appendix Aalt.comp.hardware.overclocking IS-10 / IS-11 / IS-12 / IS-20U.K. and Ireland North America and South AmericaShanghai JapanRussia France, Italy, Spain, Portugal, and GreeceUser’s Manual How to Get Technical SupportThank You ABIT Computer Corporation Technical Support Form Problem Description