If the dryer repeatedly has DSI (Direct Spark Ignition) module "LOCK-OUT" failures, the cause may be due to high voltage not getting into the DSI module ignitor probe assembly.

(1)Check to insure that the red high voltage wire (between the ignitor spark electrode and the DSI [Direct Spark Ignition] module) is not wrapped around the sensor probe wire (the wire between the DSI module FP terminal and the ignitor and flame-probe assembly). If the wires are touching one another, separate and secure in place AWAY FROM ONE ANOTHER.

(2)Check to insure that the dryer is properly grounded and that the ground connections (GND) to the DSI (Direct Spark Ignition) module are secure.

(3)If the problem persists, it is most likely to be in the external components (not the DSI [Direct Spark Ignition] module), or wiring , due to a "FLAME-OUT" ... proceed as follows:

NOTE: Preliminary steps - DO NOT OMIT - to minimize the time required to troubleshoot this system.

(a)Discontinue the electrical service to the dryer.

(b)Visually check the DSI (Direct Spark Ignition) module components for visual damage.

(c)Check wiring for loose connections, nicks or cracking at the ceramic insulator, or shorting of the sensor to the burner.

(d)Inspect the DSI (Direct Spark Ignition) ignitor and flame-probe assembly...

...check electrode for visible cracking at the ceramic insulator or shorting of sensor to burner

...check to insure that the flame sensor rod is positioned over the flame area

...check for carbon deposits on the flame sensor rod

...check to insure that there is a 1/8" gap between the ground rod and the ignitor spark electrode

b.After preforming these inspections and making corrections - if any - restore power to the dryer ... start the dryer and operate through one (1) complete cycle to insure that ALL components are functioning properly. If a no heat condition persists refer to the Troubleshooting Flow Charts on page 37, page 38, and page 39.

1)To effectively use this information or the flow charts, each step must be completed in sequence, performing whatever test are suggested. After the completion of each test, the guide will direct the Service Technician to the next logical step in the troubleshoot sequence based on the outcome of the previous check.

2)Components should be replaced only after each step has been completed and replacements after each step has been completed and replacement is suggested in the flow chart. However, the experienced technician realizes that a loose connection or broken or shorted wire may be at fault where electrical components are concerned... and not necessarily the suspected component itself.

3 5

Page 38 Page 40
Page 39
Image 39
ADC AD-310 service manual
Page 38 Page 40

AD-310 specifications

The ADC AD-310 is a versatile and compact audio digital converter designed to meet the demands of audio professionals and enthusiasts alike. With its advanced technology and user-friendly features, the AD-310 stands out in the crowded marketplace of audio interface solutions.

One of the main features of the ADC AD-310 is its high-resolution audio conversion capabilities. Supporting sample rates up to 192 kHz and resolutions of up to 24 bits, the AD-310 ensures that audio captures are of the highest fidelity, making it ideal for recording, mixing, and mastering tasks. This level of detail is crucial for audio professionals who require precision and clarity in their audio signals.

Another standout characteristic of the ADC AD-310 is its robust connectivity options. It comes equipped with both USB and optical ports, enabling seamless integration with a variety of digital audio workstations (DAWs) and other audio equipment. This flexibility allows users to choose their preferred connection method, enhancing the overall workflow and efficiency during production.

The AD-310 also features advanced analog-to-digital and digital-to-analog converters, which contribute to its impressive dynamic range and low total harmonic distortion (THD). This ensures that the audio output is clean and true to the original signal, making it suitable for both recording and playback applications. Additionally, the unit incorporates real-time monitoring capabilities, allowing users to hear adjustments as they make them, ensuring the perfect mix every time.

For ease of use, the ADC AD-310 is designed with a simple, intuitive interface. Its layout includes clearly labeled controls and LED indicators, allowing users to quickly assess levels and settings at a glance. This design philosophy extends to its compact form factor, making it easy to transport and integrate into any studio setup, whether it be in a professional environment or home studio.

With its combination of high-quality audio processing, flexible connectivity, and user-friendly design, the ADC AD-310 is an excellent choice for anyone looking to elevate their audio production experience. Whether used by professionals or hobbyists, the AD-310 delivers performance and reliability that sets it apart in the audio converter market.
Top Page Image Contents