Trigger
Trigger
Control
Trigger Function
Pressing the Shift Trigger key generates an immediate trigger
Trigger Control Functions
INIT:IMMED | Initiate trigger immediately |
INIT:CONT ON OFF | Initiate trigger continuously |
TRIG:SOUR BUS EXT | Select transient trigger source |
TTLT IMM |
|
DELAY <value> | Set trigger delay in seconds |
ABORT | Abort all trigger sequences |
SYNC:SOUR PHASE IMM | Select synchronous trigger source |
SYNC:PHASE <value> | Set synchronous phase reference |
Current
Voltage
Current Functions
CURR:LEV <value> | set immediate rms current limit4 | |
CURR:PEAK <value> | set immediate peak current limit3 | |
CURR:PEAK:T <value> | set triggered peak current limit3 | |
CURR:PEAK:M FIXED STEP | select the peak current limit mode3 | |
PULSE LIST |
| |
Voltage | Functions | |
VOLT <value> | set immediate ac output voltage4 | |
VOLT:T<value> | set triggered output voltage4 | |
VOLT:M FIXED STEP | select the voltage mode4 | |
PULSE LIST |
| |
RANGE 150 300 | set the voltage range2, 4 | |
OFFSET <value> | set immediate dc offset voltage3 | |
OFFSET:T<value> | set triggered dc offset voltage3 | |
OFFSET:M FIXED STEP | select the dc offset voltage mode3 | |
PULSE LIST |
| |
SLEW <value> | set voltage slew in V/sec4 | |
SLEW:T<value> | set triggered voltage slew in V/sec4 | |
SLEW:M FIXED STEP | select the voltage slew mode4 | |
PULSE LIST |
| |
OFF:SLW <value> | set dc offset slew in V/sec3 | |
OFF:SLW:T<value> | set triggered dc offset slew in V/sec3 | |
OFF:SLW:M FIXED STEP | select the dc offset voltage slew | |
PULSE LIST | mode3 | |
ALC INT EXT | select the voltage sense source | |
ALC:DET RTIME RMS | select the voltage sense detector3 |
Phase
Freq
| Phase Functions |
PHASE <value> | set immediate output phase4 |
PHASE:T <value> | set triggered output phase4 |
PHASE:M FIXED STEP | select the phase mode4 |
PULSE LIST |
|
| Freq Functions | |
FREQ <value> |
| set immediate output frequency |
FREQ:T<value> |
| set triggered output frequency |
FREQ:M FIXED STEP |
| select the frequency mode |
| ||
PULSE LIST |
|
|
SLEW <value> |
| set frequency slew in Hz/sec |
SLEW:T<value> |
| set triggered frequency slew Hz/sec |
| ||
SLEW:M FIXED STEP |
| select the frequency slew mode |
PULSE LIST |
|
|
| Shape |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Shape Functions | ||
| SHAPE | SINE SQUARE | set immediate shape | |||
|
|
| CSIN <user> |
| ||
| SHAPE:T | SINE SQUARE | set triggered shape | |||
|
|
| CSIN <user> |
| ||
| SHAPE:M | FIXED STEP | set shape mode | |||
|
|
| PULSE LIST |
| ||
| CLIP <value> | set clipping level | ||||
| List |
|
|
|
| |
|
|
|
|
|
|
|
| Pulse |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| List Functions | ||
| COUNT <value> | number of times a list repeats | ||||
| DWEL:<index> <value> | list of output dwell times | ||||
| FREQ:<index> <value> | list of output frequencies | ||||
| FSLW:<index> <value> | list of output frequency slew rates | ||||
| IPK:<index> <value> | list of output peak current limits3 | ||||
| OFFS:<index> <value> | list of dc output voltages3 | ||||
| OSLW:<index> <value> | dc offset voltage slew rate list3 | ||||
| PHASE:<index> <value> | list of output voltage phase | ||||
|
|
|
|
|
| angles4 |
| SHAP:<index> SINE SQUARE | list of output waveform shapes | ||||
|
|
| CSIN <user> |
| ||
| STEP ONCE AUTO | set response of list to triggers | ||||
| TTLT:<index> ON OFF | set trigger out pulse list | ||||
| VOLT:<index> <value> | list of ac output voltages4 | ||||
| VSLW:<index> <value> | list of output voltage slew rates4 | ||||
|
|
|
| Pulse | Functions | |
| WIDTH <value> | set the pulse width | ||||
| COUNT <value> | set the number of output pulses | ||||
| DCYCLE <value> | set the pulse duty cycle | ||||
| PER <value> | set the pulse period count | ||||
| qHOLD WIDTH DCYCLE | set parameter that is held constant | ||||
| Index |
| pqIndex |
| ||
| Ù |
|
| Å |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| pIndex Functions | ||
These are Shift Index keys which are used to scroll through indexed functions. Press these keys to step through integers 0 through 50 for a harmonic list, or 0 through 99 for list points. Hold down these keys to rapidly access any harmonicqor list point.
pFunctions
These keys let you move through the choices in a command list. Command lists are circular; you can return to the starting position by continuously pressing either key.
| This key applies to | |
Phase | ||
Pressing this key successively selects phase 1 | ||
Select | ||
first, followed by phase 2, phase 3, and then all | ||
| ||
| three phases. |
Output | This key toggles the output on and off. When off, |
On/Off | the ac source output is disabled and the Dis |
| annunciator is on. |
18
