The front panel menus - at a glance
SYSTEM Keys
FUNCTION Keys
Press to change the ac source’s selected interface from remote operation to local (front panel) operation. Pressing the key will have no effect if the interface state is already Local, Local-
Error Functions
Displays system error codes stored in the SCPI error queue. If no errors exist, a 0 is displayed. The Err annunciator is lit when there are errors.
Address Functions
sets the GPIB address selects an interface selects the baud rate
selects message parity selects the language selects the number of outputs1
Save Functions
Press to save an existing ac source state in nonvolatile memory. Up to 16 states can be saved
Recall Functions
Press to place the ac source into a previously saved state. Up to 16 states can be recalled
|
|
|
| Meter Functions | ||
| <reading>V <reading>Hz |
| rms voltage and frequency | |||
| <reading>V <reading>A |
| rms voltage and rms current | |||
| <reading>A <reading>Hz |
| rms current and frequency | |||
| <reading>V <reading>W |
| rms voltage and power | |||
| <reading> CREST F |
| current crest factor | |||
| <reading>A | PK REP |
| peak current, repetitive | ||
| <reading>A | PK NR |
| peak current, nonrepetitive | ||
| <reading>VA |
| apparent power | |||
| <reading> | VAR |
| reactive power | ||
| <reading>W TOTAL |
| total power all phases1 | |||
| <reading> | PFACTOR |
| power factor | ||
| <reading>A NEUTRAL |
| neutral rms current1 | |||
| Output |
|
|
|
| |
|
|
|
|
|
|
|
| Input |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| Output Functions | ||
| OUTP:COUP AC DC | select output coupling3 | ||||
| *RST |
|
| executes the *RST command | ||
| TTLT:SOUR BOT EOT LIST | select Trigger Out source coupling | ||||
| TTLT:STATE ON OFF | set Trigger Out state | ||||
| IMP:STATE ON OFF | set output impedance programming3 | ||||
| IMP:REAL <value> | set real part of output impedance3 | ||||
| IMP:REAC <value> | set reactive part of output impedance3 | ||||
| PON:STATE RST RCL0 | select | ||||
| RI LATCHING LIVE OFF | sets remote inhibit mode | ||||
| DFI ON OFF | sets discrete fault indicator state | ||||
| DFI:SOUR QUES OPER | select the DFI source | ||||
|
| ESB RQS OFF |
|
| ||
First press and release this blue shift key to select a shifted function. The Shift annunciator lights when this key is pressed.
FUNCTION Keys
Harmonic
Meter
Harmonic Functions
<reading>A I:MAG: <index> | current harmonic magnitude |
<reading>° I:PHASE: <index> | current harmonic phase |
<reading>V V:MAG: <index> | voltage harmonic magnitude |
<reading>° V:PHASE: <index> | voltage harmonic phase |
<reading> N:MAG: <index> | neutral current harmonic magnitude |
<reading>° N:PHASE: <index> | neutral current harmonic phase |
<reading> CURR:THD | current total % harmonic distortion |
<reading> VOLT:THD | voltage total % harmonic distortion |
Meter functions continued on next column
Input Functions
INP:COUP AC DC ACDC | choose meter coupling |
CURR:RANGE HIGH LOW | current measurement range3 |
WINDOW KBESSEL RECT | select harmonic measurement |
| window meter |
Status
Prot
| Status Functions | |
*CLS |
| executes the *CLS command |
STATUS:PRESET |
| executes STATus:PRESet command |
*ESR? <value> |
| return Event Status register value |
*STB <value> |
| return Status Byte register value |
OPER:EVEN? <value> |
| return STAT:OPER:EVENT? value |
OPER:COND <value> |
| return STAT:OPER:COND? value |
QUES:EVEN? <value> |
| return STAT:QUES:EVENT? value |
QUES:COND <value> |
| return STAT:QUES:COND? value |
| Protect Functions | |
PROT:CLEAR |
| clears latched protection signal |
CURR:PROT ON OFF |
| set overcurrent protection function |
VOLT:PROT ON OFF |
| set overvoltage protection function3 |
VOLT:PROT <value> |
| set overvoltage protection level |
DELAY <value> |
| set a time delay for activating a |
|
| protection fault |
17
